VENTILATION SYSTEM INFINITISWITCHES AND THEIR CONTROL FUNCTION VTL-3 < SYSTEM DESCRIPTION > C D E F G H J K L M A B VTL N O P SYSTEM DESCRIPTION SWITCHES AND THEIR CONTROL FUNCTION System Description INFOID:0000000004960918 JPIIA1243GB JSIIA1372GB VTL-4 < SYSTEM DESCRIPTION > AIR DISTRIBUTION AIR DISTRIBUTION System Description INFOID:0000000004960919 JSIIA1208GB PRECAUTIONS VTL-5 < PRECAUTION > C D E F G H J K L M A B VTL N O P PRECAUTION PRECAUTIONS FOR RUSSIA FOR RUSSIA : Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" INFOID:0000000006115304 The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted. Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this Service Manual. WARNING: • To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision that would result in air bag inflation, all maintenance must be performed by an authorized NISSAN/INFINITI dealer. • Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module, see the “SRS AIR BAG”. • Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors. PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS WARNING: • When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing serious injury. • When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the battery, and wait at least 3 minutes before performing any service. EXCEPT FOR RUSSIA EXCEPT FOR RUSSIA : Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" INFOID:0000000004960920 The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision. Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this Service Manual. WARNING: • To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision which would result in air bag inflation, all maintenance must be performed by an authorized NISSAN/INFINITI dealer. • Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module, see the “SRS AIR BAG”. • Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors. PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS WARNING: • When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) VTL-6 < PRECAUTION > PRECAUTIONS with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing serious injury. • When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the battery, and wait at least 3 minutes before performing any service. Precaution Necessary for Steering Wheel Rotation after Battery Disconnect INFOID:0000000004960921 NOTE: • Before removing and installing any control units, first turn the push-button ignition switch to the LOCK position, then disconnect both battery cables. • After finishing work, confirm that all control unit connectors are connected properly, then re-connect both battery cables. • Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work. If a DTC is detected, perform trouble diagnosis according to self-diagnosis results. For vehicle with steering lock unit, if the battery is disconnected or discharged, the steering wheel will lock and cannot be turned. If turning the steering wheel is required with the battery disconnected or discharged, follow the operation procedure below before starting the repair operation. OPERATION PROCEDURE 1. Connect both battery cables. NOTE: Supply power using jumper cables if battery is discharged. 2. Turn the push-button ignition switch to ACC position. (At this time, the steering lock will be released.) 3. Disconnect both battery cables. The steering lock will remain released with both battery cables disconnected and the steering wheel can be turned. 4. Perform the necessary repair operation. 5. When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn the push-button ignition switch from ACC position to ON position, then to LOCK position. (The steering wheel will lock when the push-button ignition switch is turned to LOCK position.) 6. Perform self-diagnosis check of all control units using CONSULT-III. Precaution for Procedure without Cowl Top Cover INFOID:0000000004960922 When performing the procedure after removing cowl top cover, cover the lower end of windshield with urethane, etc. PIIB3706J PREPARATION VTL-7 < PREPARATION > C D E F G H J K L M A B VTL N O P PREPARATION PREPARATION Commercial Service Tool INFOID:0000000004960923 Tool name Description Remover tool Remove clips, pawls, metal clips PIIB7923J VTL-8 < PERIODIC MAINTENANCE > AIR CONDITIONER FILTER PERIODIC MAINTENANCE AIR CONDITIONER FILTER Exploded View INFOID:0000000004960924 Removal and Installation INFOID:0000000004960925 REMOVAL 1. Remove instrument lower panel RH. Refer to IP-14, "A/T MODELS : Exploded View". 2. Remove filter cover (1), and then remove air conditioner filter (2). INSTALLATION Installation is basically the reverse order of removal. CAUTION: 1. Adapter 2. Intake box (right) 3. Intake door lever 2 4. Intake door motor 5. Intake door link 6. Intake door lever 1 7. Filter cover 8. Air conditioner filter 9. Intake upper case 10. Intake lower case 11. Blower motor assembly 12. Seal 13. Intake box (left) 14. Intake door 1 15. Intake door 2 JSIIA0009ZZ JSIIA1294ZZ AIR CONDITIONER FILTER VTL-9 < PERIODIC MAINTENANCE > C D E F G H J K L M A B VTL N O P • If the filter is deformed/damaged when removing, replace it with a new one. Deformed/damaged filter may deteriorate the duct collecting performance. • When installing, handle the filter with extreme care to avoid deforming/damaging. • Never open the wrap until just before the installation. Because the high performance filter (for odors, pollen, and other allergens) immediately starts absorbing odors by opening the wrap to remove them. Replacement INFOID:0000000004960926 Replace air conditioner filter. Refer to MA-7, "Periodic Maintenance". Affix a caution label inside the glove box when replacing filter. VTL-10 < REMOVAL AND INSTALLATION > DUCT AND GRILLE REMOVAL AND INSTALLATION DUCT AND GRILLE Exploded View INFOID:0000000004960927 FRONT REAR 1. Side defroster grille (front pillar garnish) (right) 2. Side defroster duct (front pillar garnish) (right) 3. Side defroster nozzle (right) 4. Defroster nozzle 5. Side defroster nozzle (left) 6. Side defroster duct (front pillar garnish) (left) 7. Side defroster grille (front pillar garnish) (left) 8. Ventilator duct (left) 9. Adaptor duct 10. Side ventilator grille (left) 11. Instrument panel assembly 12. Center ventilator grille (left) 13. Cluster lid D 14. Center ventilator grille (right) 15. Side ventilator grille (right) 16. Front defroster grille (right) 17. Ventilator duct (right) 18. Front defroster grille (left) JSIIA1313ZZ DUCT AND GRILLE VTL-11 < REMOVAL AND INSTALLATION > C D E F G H J K L M A B VTL N O P CENTER VENTILATOR GRILLE CENTER VENTILATOR GRILLE : Removal and Installation INFOID:0000000004960928 REMOVAL 1. Remove cluster lid D. Refer to IP-14, "A/T MODELS : Exploded View". 2. Remove mounting screw (A), and then remove center ventilator grilles (1) (left and right). INSTALLATION Installation is basically the reverse order of removal. SIDE VENTILATOR GRILLE SIDE VENTILATOR GRILLE : Removal and Installation INFOID:0000000004960929 REMOVAL 1. Blower unit 2. Heater & cooling unit assembly 3. Heater pipe cover 4. Heater duct 5. Foot grille (left) 6. Foot duct (left) 7. Floor carpet 8. Rear floor duct 2 (left) 9. Rear floor duct 2 (right) 10. Rear ventilator duct 2 11. Rear ventilator grille 12. Rear ventilator duct 1 13. Rear floor duct 1 14. Foot grille (right) 15. Foot duct (right) JPIIA1232ZZ : Pawl JSIIA1314ZZ VTL-12 < REMOVAL AND INSTALLATION > DUCT AND GRILLE 1. Remove ventilator duct (left and right). Refer to VTL-10, "Exploded View". 2. Remove mounting screws (A), and then remove side ventilator grille (left) (1). INSTALLATION Installation is basically the reverse order of removal. FRONT DEFROSTER GRILLE FRONT DEFROSTER GRILLE : Removal and Installation INFOID:0000000004960930 REMOVAL Remove front defroster grilles (1), using remover tools (A). INSTALLATION Installation is basically the reverse order of removal. SIDE DEFROSTER GRILLE SIDE DEFROSTER GRILLE : Removal and Installation INFOID:0000000004960931 REMOVAL Remove side defroster grilles (left and right) (1), using remover tools (A). INSTALLATION Installation is basically the reverse order of removal. VENTILATOR DUCT VENTILATOR DUCT : Removal and Installation INFOID:0000000004960932 REMOVAL 1. Remove instrument panel assembly. Refer to IP-14, "A/T MODELS : Exploded View". JSIIA1315ZZ JSIIA1317ZZ JSIIA1318ZZ DUCT AND GRILLE VTL-13 < REMOVAL AND INSTALLATION > C D E F G H J K L M A B VTL N O P 2. Remove mounting screws (A), and then remove ventilator duct (left) (1) and ventilator duct (right) (2). INSTALLATION Installation is basically the reverse order of removal. ADAPTOR DUCT ADAPTOR DUCT : Removal and Installation INFOID:0000000004960933 REMOVAL 1. Remove instrument panel assembly. Refer to IP-14, "A/T MODELS : Exploded View". 2. Remove mounting screw (A), and then remove adaptor duct (1). INSTALLATION Installation is basically the reverse order of removal. DEFROSTER NOZZLE DEFROSTER NOZZLE : Removal and Installation INFOID:0000000004960934 REMOVAL 1. Remove side defroster nozzles. Refer to VTL-10, "Exploded View". 2. Remove defroster nozzle (1). JSIIA1319ZZ JSIIA1320ZZ JPIIA0673ZZ VTL-14 < REMOVAL AND INSTALLATION > DUCT AND GRILLE INSTALLATION Installation is basically the reverse order of removal. SIDE DEFROSTER NOZZLE SIDE DEFROSTER NOZZLE : Removal and Installation INFOID:0000000004960935 REMOVAL 1. Remove instrument panel assembly. Refer to IP-14, "A/T MODELS : Exploded View". 2. Remove mounting clip (A) and harness clip (B), and then remove side defroster nozzle (left) (1). 3. Remove mounting clip (A), and then remove side defroster nozzle (right) (1). INSTALLATION Installation is basically the reverse order of removal. SIDE DEFROSTER DUCT SIDE DEFROSTER DUCT : Removal and Installation INFOID:0000000004960936 REMOVAL 1. Remove front pillar garnishes. Refer to INT-19, "Exploded View". 2. Remove mounting screws (A), and then remove side defroster ducts (left and right) (1). INSTALLATION Installation is basically the reverse order of removal. REAR VENTILATOR GRILLE JSIIA1321ZZ JSIIA1322ZZ JSIIA1323ZZ DUCT AND GRILLE VTL-15 < REMOVAL AND INSTALLATION > C D E F G H J K L M A B VTL N O P REAR VENTILATOR GRILLE : Removal and Installation INFOID:0000000004960937 REMOVAL 1. Remove console rear finisher. Refer to IP-37, "A/T MODELS : Exploded View". 2. Remove mounting screws (A), and then remove rear ventilator grille (1). INSTALLATION Installation is basically the reverse order of removal. REAR VENTILATOR DUCT 1 REAR VENTILATOR DUCT 1 : Removal and Installation INFOID:0000000004960938 REMOVAL 1. Remove center console assembly. Refer to IP-37, "A/T MODELS : Exploded View". 2. Remove mounting screws (A), and then remove rear ventilator duct 1 (1). INSTALLATION Installation is basically the reverse order of removal. REAR VENTILATOR DUCT 2 REAR VENTILATOR DUCT 2 : Removal and Installation INFOID:0000000004960939 REMOVAL 1. Remove console rear finisher. Refer to IP-37, "A/T MODELS : Exploded View". 2. Remove rear ventilator duct 2 (1). INSTALLATION : Pawl JSIIA1324ZZ JPIIA0678ZZ JSIIA1325ZZ VTL-16 < REMOVAL AND INSTALLATION > DUCT AND GRILLE Installation is basically the reverse order of removal. FOOT GRILLE FOOT GRILLE : Removal and Installation INFOID:0000000004960940 REMOVAL 1. Remove foot grille (left) (1). 2. Remove foot grille (right) (1). INSTALLATION Installation is basically the reverse order of removal. FOOT DUCT FOOT DUCT : Removal and Installation (LHD models) INFOID:0000000004960941 REMOVAL Driver Side 1. Remove heater & cooling unit assembly. Refer to HA-65, "HEATER & COOLING UNIT ASSEMBLY : Removal and Installation" (VQ37VHR), HA-131, "HEATER & COOLING UNIT ASSEMBLY : Removal and Installation" (VK50VE) or HA-193, "HEATER & COOLING UNIT ASSEMBLY : Removal and Installation" (V9X). 2. Remove mounting screws (A), and then remove heater pipe cover (1). 3. Remove mounting screws (B), and then remove foot duct (left) (2). Passenger Side 1. Set the temperature at 16.0°C. CAUTION: : Pawl JSIIA1326ZZ : Pawl JSIIA1327ZZ JSIIA1114ZZ DUCT AND GRILLE VTL-17 < REMOVAL AND INSTALLATION > C D E F G H J K L M A B VTL N O P The angle may be out, when installing the air mix door actuator to the air mix door, unless the above procedure is performed. 2. Disconnect the battery cable from the negative terminal. 3. Remove heater & cooling unit assembly. Refer to HA-65, "HEATER & COOLING UNIT ASSEMBLY : Removal and Installation" (VQ37VHR), HA-131, "HEATER & COOLING UNIT ASSEMBLY : Removal and Installation" (VK50VE) or HA-193, "HEATER & COOLING UNIT ASSEMBLY : Removal and Installation" (V9X). 4. Remove air mix door motor (passenger side). Refer to HAC-134, "Exploded View". 5. Remove mode door motor and links. Refer to HAC-134, "Exploded View". 6. Remove mounting screws (A), and then remove evaporator cover (1). 7. Remove mounting screws (B), and then remove foot duct (right) (2). INSTALLATION Installation is basically the reverse order of removal. FOOT DUCT : Removal and Installation (RHD models) INFOID:0000000004960942 REMOVAL Driver Side 1. Remove heater & cooling unit assembly. Refer to HA-65, "HEATER & COOLING UNIT ASSEMBLY : Removal and Installation" (VQ37VHR), HA-131, "HEATER & COOLING UNIT ASSEMBLY : Removal and Installation" (VK50VE) or HA-193, "HEATER & COOLING UNIT ASSEMBLY : Removal and Installation" (V9X). 2. Remove mode door motor and links. Refer to HAC-134, "Exploded View". 3. Remove mounting screws (A), and then remove heater pipe cover (1). 4. Remove mounting screws (B), and then remove foot duct (right) (2). Passenger Side 1. Set the temperature at 16.0°C. CAUTION: The angle may be out, when installing the air mix door actuator to the air mix door, unless the above procedure is performed. 2. Remove heater & cooling unit assembly. Refer to HA-65, "HEATER & COOLING UNIT ASSEMBLY : Removal and Installation" (VQ37VHR), HA-131, "HEATER & COOLING UNIT ASSEMBLY : Removal and Installation" (VK50VE) or HA-193, "HEATER & COOLING UNIT ASSEMBLY : Removal and Installation" (V9X). 3. Remove air mix door motor (passenger side). Refer to HAC-134, "Exploded View". JSIIA1115ZZ NNIIA0124ZZ VTL-18 < REMOVAL AND INSTALLATION > DUCT AND GRILLE 4. Remove mounting screws (A), and then remove evaporator cover (1). 5. Remove mounting screws (B), and then remove foot duct (left) (2). INSTALLATION Installation is basically the reverse order of removal. HEATER DUCT HEATER DUCT : Removal and Installation INFOID:0000000004960943 REMOVAL 1. Remove instrument lower panel LH. Refer to IP-14, "A/T MODELS : Exploded View". 2. Remove mounting screw (A), and then remove heater duct (1). INSTALLATION Installation is basically the reverse order of removal. REAR FLOOR DUCT 1 REAR FLOOR DUCT 1 : Removal and Installation INFOID:0000000004960944 REMOVAL 1. Remove instrument panel assembly. Refer to IP-14, "A/T MODELS : Exploded View". 2. Remove mounting clips (A), and then remove rear floor duct 1 (1). INSTALLATION Installation is basically the reverse order of removal. NNIIA0125ZZ JSIIA1328ZZ JPIIA0680ZZ BLOWER UNIT VTL-19 < REMOVAL AND INSTALLATION > C D E F G H J K L M A B VTL N O P BLOWER UNIT Exploded View INFOID:0000000004960945 DISASSEMBLY 1. Blower unit 2. Heater & cooling unit assembly 3. Steering member 4. Instrument stay (left) 5. Instrument panel assembly 6. instrument stay (right) JPIIA1223GB VTL-20 < REMOVAL AND INSTALLATION > BLOWER UNIT BLOWER UNIT BLOWER UNIT : Removal and Installation INFOID:0000000004960946 REMOVAL 1. Remove instrument lower panel RH. Refer to IP-14, "A/T MODELS : Exploded View". 2. Disconnect 4WD control unit connector. Refer to DLN-59, "Exploded View". 3. Disconnect ECM (1) connectors. 4. Remove mounting nuts (A), and then remove ECM with bracket attached. 5. Remove power steering control unit. Refer to STC-24, "Exploded View" (WITHOUT REAR ACTIVE STEER) or STC-106, "Exploded View" (WITH REAR ACTIVE STTER). 6. Disconnect intake door motor connector and blower motor connector. 1. Adapter 2. Intake box (right) 3. Intake door lever 2 4. Intake door motor 5. Intake door link 6. Intake door lever 1 7. Filter cover 8. In-cabin microfilter 9. Intake upper case 10. Intake lower case 11. Blower motor assembly 12. Seal 13. Intake box (left) 14. Intake door 1 15. Intake door 2 JSIIA0009ZZ JSIIA1302ZZ BLOWER UNIT VTL-21 < REMOVAL AND INSTALLATION > C D E F G H J K L M A B VTL N O P 7. Remove mounting bolt (A) and screw (B), from blower unit (1). 8. Remove blower unit. CAUTION: Move blower unit rightward, and remove locating pin (1 part) and joint. Then remove blower unit downward. INSTALLATION Installation is basically the reverse order of removal. CAUTION: Make sure locating pin (A) and joint (B) are securely inserted. BLOWER MOTOR BLOWER MOTOR : Removal and Installation INFOID:0000000004960947 REMOVAL 1. Remove instrument lower cover RH. Refer to IP-14, "A/T MODELS : Exploded View". 2. Disconnect blower motor connector. 3. Remove mounting screws (A), and then remove blower motor (1). INSTALLATION Installation is basically the reverse order of removal. |