WARNING CHIME SYSTEM INFINITI[html]
HOW TO USE THIS SECTION WCS-3 < HOW TO USE THIS MANUAL > C D E F G H I J K L M B A O P HOW TO USE THIS MANUAL HOW TO USE THIS SECTION Information INFOID:0000000006059752 Both “VDC”and “ESP” are used in this manual. These indicate the same system. WCS-4 < BASIC INSPECTION > DIAGNOSIS AND REPAIR WORKFLOW BASIC INSPECTION DIAGNOSIS AND REPAIR WORKFLOW Work Flow INFOID:0000000004968244 OVERALL SEQUENCE DETAILED FLOW 1.OBTAIN INFORMATION ABOUT SYMPTOM Interview the customer to obtain as much information as possible about the conditions and environment under which the malfunction occurred. >> GO TO 2. 2.CHECK SYMPTOM • Check the symptom based on the information obtained from the customer. • Check that any other malfunctions are present. >> GO TO 3. 3.CHECK CONSULT-III SELF-DIAGNOSIS RESULTS Connect CONSULT-III and perform self-diagnosis. Refer to MWI-44, "CONSULT-III Function (METER/M&A)". JSNIA0456GB WCS DIAGNOSIS AND REPAIR WORKFLOW WCS-5 < BASIC INSPECTION > C D E F G H I J K L M B A O P Are self-diagnosis results normal? YES >> GO TO 4. NO >> GO TO 5. 4.NARROW DOWN MALFUNCTIONING PARTS BY SYMPTOM DIAGNOSIS Perform symptom diagnosis and narrow down the malfunctioning parts. >> GO TO 5. 5.REPAIR OR REPLACE MALFUNCTIONING PARTS Repair or replace malfunctioning parts. NOTE: If DTC is displayed, erase DTC after repair or replace malfunctioning parts. >> GO TO 6. 6.FINAL CHECK Check that the warning buzzer in the combination meter operates normally. Does it operate normally? YES >> INSPECTION END NO >> GO TO 1. WCS-6 < SYSTEM DESCRIPTION > WARNING CHIME SYSTEM SYSTEM DESCRIPTION WARNING CHIME SYSTEM WARNING CHIME SYSTEM WARNING CHIME SYSTEM : System Diagram INFOID:0000000004968245 EXCEPT FOR RUSSIA FOR RUSSIA WARNING CHIME SYSTEM : System Description INFOID:0000000004968246 COMBINATION METER JPNIA1262GB JPNIA1207GB WCS WARNING CHIME SYSTEM WCS-7 < SYSTEM DESCRIPTION > C D E F G H I J K L M B A O P • The buzzer (1) for warning chime system is installed in the combination meter. • The buzzer sounds when the combination meter receives buzzer output signal from each unit through unified meter and A/C amp. UNIFIED METER AND A/C AMP. The unified meter and A/C amp. receives signal from various units and switches and transmits the buzzer output signal to the combination meter. BCM BCM receives signals from various units and transmits a buzzer output signal to the unified meter and A/C amp. with CAN communication line if it judges that the warning buzzer should be activated. BCM warning function list Except for Russia BCM warning function list For Russia WARNING CHIME SYSTEM : Component Parts Location INFOID:0000000004968247 JPNIA0764ZZ Warning functions Signal name Light reminder warning chime • Combination switch INPUT signal • Driver door switch signal Front fog light reminder warning chime Combination switch INPUT signal Warning functions Signal name Light reminder warning chime • Combination switch INPUT signal • Driver door switch signal Seat belt warning chime Seat belt buckle switch signal 1. BCM 2. ABS actuator and electric unit (control unit) 3. Unified meter and A/C amp. 4. Front door switch (driver side) 5. Parking brake switch (M/T models) 6. Combination switch (Lighting switch) JSNIA3071ZZ WCS-8 < SYSTEM DESCRIPTION > WARNING CHIME SYSTEM WARNING CHIME SYSTEM : Component Description INFOID:0000000004968248 LIGHT REMINDER WARNING CHIME LIGHT REMINDER WARNING CHIME : System Diagram INFOID:0000000004968249 LIGHT REMINDER WARNING CHIME : System Description INFOID:0000000004968250 DESCRIPTION 7. Parking brake switch (A/T models) 8. Seat belt buckle switch (driver side) 9. Seat belt buckle switch (passenger side) 10. Occupant detection unit 11. Combination meter Unit Description Combination meter • Receives a buzzer output signal from the unified meter and A/C amp. and sounds the buzzer. • Judges whether the parking brake is released from the vehicle speed signal received from the unified meter and A/C amp. with CAN communication line and the parking brake switch signal from the parking brake switch, and sounds the buzzer if necessary. Unified meter and A/C amp. Except for Russia • Receives a seat belt buckle switch signal from seat belt buckle switches. • Receives a buzzer output signal (light reminder warning chime, front fog light reminder warning chime) from BCM with CAN communication line. • Transmits a buzzer output signal (light reminder warning chime, front fog light reminder warning chime, seat belt reminder warning chime) to the combination meter with communication line. For Russia • Receives the seat belt buckle switch signal from the seat belt buckle switch and transmits it to BCM with CAN communication line. • Receives a buzzer output signal (light reminder warning chime, seat belt warning chime) from BCM with CAN communication line and transmits it to the combination meter by means of communication line. BCM Transmits signals provided by various units and switches to the unified meter and A/C amp. with CAN communication line. ABS actuator and electric unit (control unit) Transmits the vehicle speed signal to unified meter and A/C amp. with CAN communication line. Seat belt buckle switch (driver side) Refer to WCS-28, "Description". Seat belt buckle switch (passenger side) Refer to WCS-30, "Description". Occupant detection unit Transmits a occupant detection signal to the seat belt buckle switch (passenger side). Combination switch (lighting switch) Transmits the combination switch INPUT signal to BCM. Front door switch (driver side) Transmits the driver door switch signal to BCM. Parking brake switch Refer to MWI-72, "Description". JPNIA1271GB WCS WARNING CHIME SYSTEM WCS-9 < SYSTEM DESCRIPTION > C D E F G H I J K L M B A O P With ignition switch in OFF or ACC position, driver door open, and lighting switch in 1ST or 2ND position, the light reminder warning chime will sound. • BCM detects ignition switch in OFF or ACC position, front door switch (driver side) ON, and lighting switch in 1ST or 2ND position. And then transmits buzzer output signal (light reminder warning chime) to unified meter and A/C amp. with CAN communication line. • Unified meter and A/C amp. transmits buzzer output signal (light reminder warning chime) to combination meter with communication line. • When combination meter receives buzzer output signal (light reminder warning chime), it sounds the buzzer. WARNING OPERATION CONDITIONS If all of the following conditions are fulfilled. • Lighting switch is at 1ST or 2ND position • Ignition switch is at OFF or ACC • Front door switch (driver side) is ON WARNING CANCEL CONDITIONS Warning is canceled if any of the following conditions is fulfilled. • Lighting switch OFF • Ignition switch ON • Front door switch (driver side) is OFF LIGHT REMINDER WARNING CHIME : Component Parts Location INFOID:0000000006064522 LIGHT REMINDER WARNING CHIME : Component Description INFOID:0000000004968252 1. BCM 2. ABS actuator and electric unit (control unit) 3. Unified meter and A/C amp. 4. Front door switch (driver side) 5. Parking brake switch (M/T models) 6. Combination switch (Lighting switch) 7. Parking brake switch (A/T models) 8. Seat belt buckle switch (driver side) 9. Seat belt buckle switch (passenger side) 10. Occupant detection unit 11. Combination meter JSNIA3071ZZ Unit Description Combination meter Receives a buzzer output signal from the unified meter and A/C amp. and sounds the buzzer. Unified meter and A/C amp. Receives a buzzer output signal from BCM via CAN communication line and transmits it to the combination meter by means of communication line. BCM Judges the light warning conditions from the signals provided by various switches and transmits a buzzer output signal to the unified meter and A/C amp. via CAN communication line if necessary. WCS-10 < SYSTEM DESCRIPTION > WARNING CHIME SYSTEM FRONT FOG LIGHT REMINDER WARNING CHIME FRONT FOG LIGHT REMINDER WARNING CHIME : System Diagram INFOID:0000000004968253 FRONT FOG LIGHT REMINDER WARNING CHIME : System Description INFOID:0000000004968254 DESCRIPTION When ignition switch is switched to OFF with lighting switch in AUTO position and front fog lamp switch ON, the front fog light reminder warning chime sounds for 2 seconds. • BCM transmits buzzer output signal (front fog light reminder warning chime) to unified meter and A/C amp. with CAN communication line when ignition switch is switched to OFF with lighting switch in AUTO position and front fog lamp switch ON. • Unified meter and A/C amp. transmits buzzer output signal (front fog light reminder warning chime) to combination meter with communication line. • When combination meter receives buzzer output signal (front light reminder warning chime), it sounds the buzzer. WARNING OPERATION CONDITIONS If all of the following conditions are fulfilled. • Lighting switch is at AUTO position • Front fog lamp switch is ON • Ignition switch is at ON to OFF WARNING CANCEL CONDITIONS Warning is canceled if any of the following conditions is fulfilled. • Lighting switch is OFF • Front fog lamp switch is OFF • 2 seconds have passed since the start of the warning • Ignition switch is at OFF to ON or cranking Combination switch (Lighting switch) Transmits the combiantion switch INPUT signal to BCM. Front door switch (driver side) Transmits the driver door switch signal to BCM. Unit Description JPNIA1272GB WCS WARNING CHIME SYSTEM WCS-11 < SYSTEM DESCRIPTION > C D E F G H I J K L M B A O P FRONT FOG LIGHT REMINDER WARNING CHIME : Component Parts Location INFOID:0000000006064523 FRONT FOG LIGHT REMINDER WARNING CHIME : Component Description INFOID:0000000004968256 SEAT BELT REMAINDER WARNING CHIME EXCEPT FOR RUSSIA SEAT BELT REMAINDER WARNING CHIME EXCEPT FOR RUSSIA : System Dia- 1. BCM 2. ABS actuator and electric unit (control unit) 3. Unified meter and A/C amp. 4. Front door switch (driver side) 5. Parking brake switch (M/T models) 6. Combination switch (Lighting switch) 7. Parking brake switch (A/T models) 8. Seat belt buckle switch (driver side) 9. Seat belt buckle switch (passenger side) 10. Occupant detection unit 11. Combination meter JSNIA3071ZZ Unit Description Combination meter Receives a buzzer output signal from the unified meter and A/C amp. and sounds the buzzer. Unified meter and A/C amp. Receives a buzzer output signal (front fog light reminder warning chime) from BCM via CAN communication line and transmits it to the combination meter by means of communication line. BCM Judges the front fog light warning conditions based on the combination switch INPUT signal provided by combination switch and transmits a buzzer output signal (front fog light reminder warning chime) to the unified meter and A/C amp. via CAN communication line. Combination switch (Lighting switch) Transmits the combination switch INPUT signal to BCM. WCS-12 < SYSTEM DESCRIPTION > WARNING CHIME SYSTEM gram INFOID:0000000004968257 SEAT BELT REMAINDER WARNING CHIME EXCEPT FOR RUSSIA : System Description INFOID:0000000004968258 DESCRIPTION • The unified meter and A/C amp. receives a seat belt buckle switch signal (driver side) from the seat belt buckle switch (driver side) and seat belt buckle switch signal (passenger side) from the seat belt buckle switch (passenger side) and the occupant detection unit. • The unified meter and A/C amp. receives a vehicle speed signals from ABS actuator and electric unit (control unit) via CAN communication line. • The unified meter and A/C amp. judges a seat belt warning condition based on the signals received from each unit and switch to transmit a buzzer output signal (seat belt reminder warning chime) to the combination meter. • The combination meter sounds the seat belt reminder warning chime when receiving a buzzer output signal (seat belt reminder warning chime) from the unified meter A/C amp. WARNING OPERATION CONDITIONS If all of the following conditions are fulfilled. • Ignition switch ON • When driver seat belt is not fastened [driver side or passenger side (when getting in the passenger side)] • Vehicle speed approximately 15 km/h (9.3 MPH) or more WARNING CANCEL CONDITIONS Warning is canceled if any of the following conditions is fulfilled. • Ignition switch OFF • When driver seat belt is not fastened [driver side and passenger side (when getting in the passenger side)] • 90 seconds have passed since the start of the warning NOTE: • Seat belt reminder warning chime continues sounding even when a vehicle speed becomes less than 15 km/h. • After a lapse of 90 seconds or more, if the seat belt is unfastened again, then buzzer sounds. SEAT BELT REMAINDER WARNING CHIME EXCEPT FOR RUSSIA : Component JPNIA1180GB WCS WARNING CHIME SYSTEM WCS-13 < SYSTEM DESCRIPTION > C D E F G H I J K L M B A O P Parts Location INFOID:0000000006064524 SEAT BELT REMAINDER WARNING CHIME EXCEPT FOR RUSSIA : Component Description INFOID:0000000004968260 SEAT BELT WARNING CHIME FOR RUSSIA 1. BCM 2. ABS actuator and electric unit (control unit) 3. Unified meter and A/C amp. 4. Front door switch (driver side) 5. Parking brake switch (M/T models) 6. Combination switch (Lighting switch) 7. Parking brake switch (A/T models) 8. Seat belt buckle switch (driver side) 9. Seat belt buckle switch (passenger side) 10. Occupant detection unit 11. Combination meter JSNIA3071ZZ Unit Description Combination meter Receives a buzzer output signal from the unified meter and A/C amp. and sounds the buzzer. Unified meter and A/C amp. • Receives the seat belt buckle switch signal from the seat belt buckle switches. • The unified mete and A/C amp. judges a seat belt reminder warning condition based on the signals received from each unit and switch to transmit a buzzer output signal (seat belt warning chime) to the combination meter. Seat belt buckle switch (driver side) Refer to WCS-28, "Description". Seat belt buckle switch (passenger side) Refer to WCS-30, "Description". Occupant detection unit Transmits the occupant detection signal to the seat belt buckle switch (passenger side). ABS actuator and electric unit (control unit) Transmits the vehicle speed signal to the combination meter via CAN communication line. WCS-14 < SYSTEM DESCRIPTION > WARNING CHIME SYSTEM SEAT BELT WARNING CHIME FOR RUSSIA : System Diagram INFOID:0000000006064449 SEAT BELT WARNING CHIME FOR RUSSIA : System Description INFOID:0000000006064450 DESCRIPTION With ignition switch turned ON and driver seat belt unfastened, seat belt warning chime will sound for approximately 6 seconds. • BCM receives seat belt buckle switch signal from unified meter and A/C amp. with CAN communication line. • BCM detects ignition switch turned ON and seat belt buckle switch (driver side) ON. And then transmits buzzer output signal (seat belt warning chime) to unified meter and A/C amp. with CAN communication line. • Unified meter and A/C amp. transmits buzzer output signal (seat belt warning chime) to combination meter with communication line. • When combination meter receives buzzer output signal (seat belt warning chime), it sounds the buzzer. WARNING OPERATION CONDITIONS If all of the following conditions are fulfilled. • Ignition switch OFF→ON • Seat belt buckle switch (driver side) is ON (driver seat belt not fastened) WARNING CANCEL CONDITIONS Warning is canceled if any of the following conditions is fulfilled. • Ignition switch OFF • Seat belt buckle switch (driver side) is OFF (driver seat belt fastened) SEAT BELT WARNING CHIME FOR RUSSIA : Component Parts Location INFOID:0000000006064525 JSNIA0168GB 1. BCM 2. ABS actuator and electric unit (control unit) 3. Unified meter and A/C amp. 4. Front door switch (driver side) 5. Parking brake switch (M/T models) 6. Combination switch (Lighting switch) JSNIA3071ZZ WCS WARNING CHIME SYSTEM WCS-15 < SYSTEM DESCRIPTION > C D E F G H I J K L M B A O P SEAT BELT WARNING CHIME FOR RUSSIA : Component Description INFOID:0000000006064452 PARKING BRAKE RELEASE WARNING CHIME PARKING BRAKE RELEASE WARNING CHIME : System Diagram INFOID:0000000004968261 PARKING BRAKE RELEASE WARNING CHIME : System Description INFOID:0000000004968262 DESCRIPTION • The unified meter and A/C amp. receives the vehicle speed signal from the ABS actuator and electric unit (control unit) via CAN communication line and transmits it to the combination meter by means of communication line. • The combination meter judges whether the parking brake is released from the vehicle speed signal received from the unified meter and A/C amp. and the parking brake switch signal from the parking brake switch, and sounds the warning buzzer if necessary. WARNING OPERATION CONDITIONS If all of the following conditions are fulfilled. • Vehicle speed is 7 km/h (4.3 MPH) or higher • Parking brake switch ON WARNING CANCEL CONDITIONS Warning is canceled if any of the following conditions is fulfilled. • Vehicle speed is approximately 3 km/h (1.9 MPH) or less • Parking brake switch OFF 7. Parking brake switch (A/T models) 8. Seat belt buckle switch (driver side) 9. Seat belt buckle switch (passenger side) 10. Occupant detection unit 11. Combination meter Unit Description Combination meter Receives a buzzer output signal from the unified meter and A/C amp. and sounds the buzzer. Unified meter and A/C amp. • Receives the seat belt buckle switch signal from the seat belt buckle switch and transmits it to BCM via CAN communication line. • Receives a buzzer output signal from BCM via CAN communication line and transmits it to the combination meter by means of communication line. BCM Judges the seat belt warning condition from the seat belt buckle switch signal received from the unified meter and A/C amp. and transmits a buzzer output signal to the unified meter and A/C amp. via CAN communication line if necessary. Seat belt buckle switch (driver side) Refer to WCS-28, "Description". JSNIA0036GB WCS-16 < SYSTEM DESCRIPTION > WARNING CHIME SYSTEM PARKING BRAKE RELEASE WARNING CHIME : Component Parts Location INFOID:0000000006064526 PARKING BRAKE RELEASE WARNING CHIME : Component Description INFOID:0000000004968264 1. BCM 2. ABS actuator and electric unit (control unit) 3. Unified meter and A/C amp. 4. Front door switch (driver side) 5. Parking brake switch (M/T models) 6. Combination switch (Lighting switch) 7. Parking brake switch (A/T models) 8. Seat belt buckle switch (driver side) 9. Seat belt buckle switch (passenger side) 10. Occupant detection unit 11. Combination meter JSNIA3071ZZ Unit Description Combination meter Judges whether the parking brake is released from the vehicle speed signal received from the unified meter and A/C amp. via CAN communication line and the parking brake switch signal from the parking brake switch, and sounds the buzzer if necessary. Unified meter and A/C amp. Receives a vehicle speed signal from ABS actuator and electric unit (control unit) via CAN communication line and transmits it to the combination meter by means of communication line. ABS actuator and electric unit (control unit) Transmits the vehicle speed signal to unified meter and A/C amp. via CAN communication line. Parking brake switch Refer to MWI-72, "Description". WCS DIAGNOSIS SYSTEM (UNIFIED METER AND A/C AMP.) WCS-17 < SYSTEM DESCRIPTION > C D E F G H I J K L M B A O P DIAGNOSIS SYSTEM (UNIFIED METER AND A/C AMP.) CONSULT-III Function (METER/M&A) INFOID:0000000005383546 CONSULT-III APPLICATION ITEMS CONSULT-III can perform the following diagnosis modes with CAN communication with the unified meter and A/C amp. SELF DIAG RESULT Refer to WCS-76, "DTC Index". DATA MONITOR Display Item List X: Applicable System Diagnosis mode Description METER/M&A Self Diagnostic Result Unified meter and A/C amp. checks the conditions and displays memorized error. Data Monitor Displays unified meter and A/C amp. input/output data in real time. Ecu Identification The unified meter and A/C amp. part number is displayed. Display item [Unit] MAIN SIGNALS Description SPEED METER [km/h] or [mph] X Value of vehicle speed signal received from ABS actuator and electric unit (control unit) with CAN communication line. NOTE: 655.35 is displayed when the malfunction signal is received. SPEED OUTPUT [km/h] or [mph] X Vehicle speed signal value transmitted to other units with CAN communication line. NOTE: 655.35 is displayed when the malfunction signal is received. ODO OUTPUT [km/h] Odometer signal value transmitted to other units with CAN communication line. TACHO METER [rpm] X Value of the engine speed signal received from ECM with CAN communication line. NOTE: 8191.875 is displayed when the malfunction signal is received. FUEL METER [L] X Fuel level indicated on combination meter. W TEMP METER [°C] or [°F] X Value of engine coolant temperature signal received from ECM with CAN communication line. NOTE: 215 is displayed when the malfunction signal is input. ABS W/L [On/Off] Status of ABS warning lamp judged from ABS warning lamp signal received from ABS actuator and electric unit (control unit) with CAN communication line. VDC/TCS IND [On/Off] Status of ESP OFF indicator lamp judged from ESP OFF indicator lamp signal received from ABS actuator and electric unit (control unit) with CAN communication line. SLIP IND [On/Off] Status of SLIP indicator lamp judged from SLIP indicator lamp signal received from ABS actuator and electric unit (control unit) with CAN communication line. BRAKE W/L [On/Off] Status of brake warning lamp judged from brake warning lamp signal received from ABS actuator and electric unit (control unit) with CAN communication line. NOTE: Displays “Off” if the brake warning lamp is illuminated when the valve check starts, the parking brake switch is turned ON or the brake fluid level switch is turned ON. DOOR W/L [On/Off] Status of door warning judged from door switch signal received from BCM with CAN communication line. HI-BEAM IND [On/Off] Status of high beam indicator lamp judged from high beam request signal received from BCM with CAN communication line. WCS-18 < SYSTEM DESCRIPTION > DIAGNOSIS SYSTEM (UNIFIED METER AND A/C AMP.) TURN IND [On/Off] Status of turn indicator lamp judged from turn indicator signal received from BCM with CAN communication line. FR FOG IND [On/Off] Status of front fog indicator lamp judged from front fog light request signal received from BCM with CAN communication line. RR FOG IND [On/Off] Status of rear fog indicator lamp judged from rear fog light request signal received from BCM with CAN communication line. LIGHT IND [On/Off] Status of tail lamp indicator lamp judged from position light request signal received from BCM with CAN communication line. OIL W/L [On/Off] Status of oil pressure warning lamp judged from oil pressure switch signal received from IPDM E/R with CAN communication line. MIL [On/Off] Status of malfunction indicator lamp judged from malfunctioning indicator lamp signal received from ECM with CAN communication line. GLOW IND [On/Off] Status of glow indicator lamp judged from glow indicator lamp signal received from ECM with CAN communication line. C-ENG2 W/L [Off] This item is displayed, but cannot be monitored. CRUISE IND [On/Off] • Status of CRUISE indicator judged from ASCD status signal received from ECM with CAN communication line. • Status of CRUISE indicator judged from meter display signal received from ICC sensor integrated unit with CAN communication line. SET IND [On/Off] • Status of SET indicator judged from ASCD status signal received from ECM with CAN communication line. • Status of SET indicator judged from meter display signal received from ICC sensor integrated unit with CAN communication line. CRUISE W/L [On/Off] Status of CRUISE warning lamp judged from ICC warning lamp signal received from ICC sensor integrated unit with CAN communication line. BA W/L [On/Off] Status of IBA OFF indicator lamp judged from IBA OFF indicator signal received from ICC sensor integrated unit with CAN communication line. ATC/T-AMT W/L [On/Off] Status of A/T check warning lamp judged from A/T check indicator lamp signal received from TCM with CAN communication line. 4WD W/L [On/Off] Status of 4WD warning lamp judged from 4WD warning lamp signal received from 4WD control unit with CAN communication line. 4WD LOCK IND [Off] This item is displayed, but cannot be monitored. FUEL W/L [On/Off] Low-fuel warning status judged by the identified fuel level. WASHER W/L [On/Off] Status of washer warning judged from washer level switch input to combination meter. AIR PRES W/L [On/Off] Status of low tire pressure warning lamp judged from tire pressure signal received from BCM with CAN communication line. KEY G/Y W/L [On/Off] Status of key warning lamp (G/Y) judged from key warning signal received from BCM with CAN communication line. AFS OFF IND [On/Off] Status of AFS OFF indicator lamp judged from AFS OFF indicator lamp signal received from AFS control unit with CAN communication line. 4WAS/RAS W/L [On/Off] Status of RAS warning lamp judged from RAS warning lamp signal received from RAS control unit with CAN communication line. HDC W/L [Off] This item is displayed, but cannot be monitored. DDS W/L [Off] This item is displayed, but cannot be monitored. LANE W/L [On/Off] Status of lane departure warning lamp judged from lane departure warning lamp signal received from lane camera unit with CAN communication line. Display item [Unit] MAIN SIGNALS Description WCS DIAGNOSIS SYSTEM (UNIFIED METER AND A/C AMP.) WCS-19 < SYSTEM DESCRIPTION > C D E F G H I J K L M B A O P LDP IND [On/Off] Status of LDP ON indicator lamp judged from LDP ON indicator lamp signal received from lane camera unit with CAN communication line. E-SUS IND [On/Off] Status of sports mode indicator lamp judged from sports mode indicator lamp signal received from E-SUS control unit with CAN communication line. DCA IND [Off] This item is displayed, but cannot be monitored. LCD [b] Displays status of Intelligent Key system warning judged from meter display signal received from BCM with CAN communication line. ACC TARGET [On/Off] Status of vehicle ahead detection indicator judged from meter display signal received from ICC sensor integrated unit with CAN communication line. ACC DISTANCE [Off, SHOR, MID, LONG] Status of set distance indicator judged from meter display signal received from ICC sensor integrated unit with CAN communication line. ACC OWN VHL [On/Off] Status of own vehicle indicator judged from meter display signal received from ICC sensor integrated unit with CAN communication line. ACC SET SPEED Status of set vehicle speed indicator judged from meter display signal received from ICC sensor integrated unit with CAN communication line. ACC UNIT [On/Off] Status of display unit judged from meter display signal received from ICC sensor integrated unit with CAN communication line. SHIFT IND [P, R, N, D, L, M1, M2, M3, M4, M5, M6, M7] Status of shift position indicator judged from shift position signal and manual mode indicator signal received from TCM with CAN communication line. O/D OFF SW [Off] This item is displayed, but cannot be monitored. AT S MODE SW [On/Off] Status of snow mode switch. AT P MODE SW [Off] This item is displayed, but cannot be monitored. M RANGE SW [On/Off] Status of manual mode switch. NM RANGE SW [On/Off] Status of not manual mode switch. AT SFT UP SW [On/Off] Status of A/T shift up switch. AT SFT DWN SW [On/Off] Status of A/T shift down switch. ST SFT UP SW [On/Off] Status of paddle shifter up switch. ST SFT DWN SW [On/Off] Status of paddle shifter down switch. COMP F/B SIG [On/Off] A/C compressor activation condition that ECM judges according to the water temperature and the acceleration degree. 4WD LOCK SW [Off] This item is displayed, but cannot be monitored. PKB SW [On/Off] Status of parking brake switch. BUCKLE SW [On/Off] Status of seat belt buckle switch. BRAKE OIL SW [On/Off] Status of brake fluid level switch. DISTANCE [km/h] Value of possible driving distance calculated by unified meter and A/C amp. Display item [Unit] MAIN SIGNALS Description WCS-20 < SYSTEM DESCRIPTION > DIAGNOSIS SYSTEM (UNIFIED METER AND A/C AMP.) NOTE: Some items are not available according to vehicle specification. OUTSIDE TEMP [°C] or [°F] Ambient air temperature value converted from ambient sensor signal received from ambient sensor. NOTE: This may not match with the temperature value indicated on the information display. (Because the information display value is a corrected value from the ambient sensor input value.) FUEL LOW SIG [On/Off] Status of fuel level low warning signal to output to AV control unit with CAN communication line. CRANKING SIG [On/Off] Status of cranking judged from engine status signal received from BCM with CAN communication line. ST CNT SIG [On/Off] Status of starter relay status signal received from BCM with CAN communication line. DOOR LOCK SIG [Off] This item is displayed, but cannot be monitored. DR DOOR SIG [Off] This item is displayed, but cannot be monitored. BUZZER [On/Off] X Buzzer status (in the combination meter) is judged with the buzzer output signal received from each unit with CAN communication line and the warning output condition of the combination meter. ASCD REQ SPD [On/Off] ASCD or speed limiter set vehicle speed value that is judged by ASCD status signal received from ECM via CAN communication. ASCD STATUS [Off, ASCD, CRUISE, SL ON, SL SET] Display status of ASCD and speed limiter status display judged by the ASCD status signal received from ECM via CAN communication. ASCD SPD BLNK [On/Off] Blinking status of ASCD or speed limiter set vehicle speed that is judged by the ASCD status signal received from ECM via CAN communication. Display item [Unit] MAIN SIGNALS Description WCS DIAGNOSIS SYSTEM (BCM) WCS-21 < SYSTEM DESCRIPTION > C D E F G H I J K L M B A O P DIAGNOSIS SYSTEM (BCM) COMMON ITEM COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM) INFOID:0000000005457395 APPLICATION ITEM CONSULT-III performs the following functions via CAN communication with BCM. SYSTEM APPLICATION BCM can perform the following functions for each system. NOTE: It can perform the diagnosis modes except the following for all sub system selection items. ×: Applicable item NOTE: *: This item is displayed, but is not used. FREEZE FRAME DATA (FFD) The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on CONSULT-III. Diagnosis mode Function Description Work Support Changes the setting for each system function. Self Diagnostic Result Displays the diagnosis results judged by BCM. CAN Diag Support Monitor Monitors the reception status of CAN communication viewed from BCM. Refer to CONSULT-III operation manual. Data Monitor The BCM input/output signals are displayed. Active Test The signals used to activate each device are forcibly supplied from BCM. Ecu Identification The BCM part number is displayed. Configuration • Read and save the vehicle specification. • Write the vehicle specification when replacing BCM. System Sub system selection item Diagnosis mode Work Support Data Monitor Active Test Door lock DOOR LOCK × × × Rear window defogger REAR DEFOGGER × × Warning chime BUZZER × × Interior room lamp timer INT LAMP × × × Exterior lamp HEAD LAMP × × × Wiper and washer WIPER × × Turn signal and hazard warning lamps FLASHER × × × — AIR CONDITONER* • Intelligent Key system • Engine start system INTELLIGENT KEY × × × Combination switch COMB SW × Body control system BCM × IVIS - NATS IMMU × × Interior room lamp battery saver BATTERY SAVER × × × Back door open TRUNK × × Vehicle security system THEFT ALM × × × RAP system RETAINED PWR × Signal buffer system SIGNAL BUFFER × × WCS-22 < SYSTEM DESCRIPTION > DIAGNOSIS SYSTEM (BCM) BUZZER BUZZER : CONSULT-III Function (BCM - BUZZER) INFOID:0000000004968267 CONSULT-III APPLICATION ITEMS DATA MONITOR CONSULT screen item Indication/Unit Description Vehicle Speed km/h Vehicle speed of the moment a particular DTC is detected Odo/Trip Meter km Total mileage (Odometer value) of the moment a particular DTC is detected Vehicle Condition SLEEP>LOCK Power position status of the moment a particular DTC is detected While turning BCM status from low power consumption mode to normal mode (Power supply position is “LOCK”.) SLEEP>OFF While turning BCM status from low power consumption mode to normal mode (Power supply position is “OFF”.) LOCK>ACC While turning power supply position from “LOCK” to “ACC” ACC>ON While turning power supply position from “ACC” to “IGN” RUN>ACC While turning power supply position from “RUN” to “ACC” (Vehicle is stopping and selector lever is except P position.) CRANK>RUN While turning power supply position from “CRANKING” to “RUN” (From cranking up the engine to run it) RUN>URGENT While turning power supply position from “RUN“ to “ACC” (Emergency stop operation) ACC>OFF While turning power supply position from “ACC” to “OFF” OFF>LOCK While turning power supply position from “OFF” to “LOCK” OFF>ACC While turning power supply position from “OFF” to “ACC” ON>CRANK While turning power supply position from “IGN” to “CRANKING” OFF>SLEEP While turning BCM status from normal mode (Power supply position is “OFF”.) to low power consumption mode LOCK>SLEEP While turning BCM status from normal mode (Power supply position is “LOCK”.) to low power consumption mode LOCK Power supply position is “LOCK” (Ignition switch OFF with steering is locked.) OFF Power supply position is “OFF” (Ignition switch OFF with steering is unlocked.) ACC Power supply position is “ACC” (Ignition switch ACC) ON Power supply position is “IGN” (Ignition switch ON with engine stopped) ENGINE RUN Power supply position is “RUN” (Ignition switch ON with engine running) CRANKING Power supply position is “CRANKING” (At engine cranking) IGN Counter 0 - 39 The number of times that ignition switch is turned ON after DTC is detected • The number is 0 when a malfunction is detected now. • The number increases like 1 → 2 → 3...38 → 39 after returning to the normal condition whenever ignition switch OFF → ON. • The number is fixed to 39 until the self-diagnosis results are erased if it is over 39. Test item Diagnosis mode Description BUZZER Data Monitor Displays BCM input data in real time. Active Test Operation of electrical loads can be checked by sending driving signal to them. WCS DIAGNOSIS SYSTEM (BCM) WCS-23 < SYSTEM DESCRIPTION > C D E F G H I J K L M B A O P ACTIVE TEST Display item [Unit] Description PUSH SW [On/Off] Status of push button ignition switch judged by BCM. UNLK SEN-DR [On/Off] Status of unlock sensor judged by BCM. VEH SPEED 1 [Km/h or mph] Value of vehicle speed signal received from ABS actuator and electric unit (control unit) with CAN communication line. KEY SW-SLOT [On/Off] Status of key slot judged by BCM. TAIL LAMP SW [On/Off] Status of each switch judged by BCM using the combination switch readout function. FR FOG SW [On/Off] Status of front fog lamp switch judged by BCM. DOOR SW-DR [On/Off] Status of driver side door switch judged by BCM. Display item [Unit] Description IGN KEY WARN ALM The key warning chime operation can be checked by operating the relevant function (On/Off). SEAT BELT WARN TEST The seat belt warning chime operation can be checked by operating the relevant function (On/Off). LIGHT WARN ALM The light warning chime operation can be checked by operating the relevant function (On/Off). WCS-24 < DTC/CIRCUIT DIAGNOSIS > POWER SUPPLY AND GROUND CIRCUIT DTC/CIRCUIT DIAGNOSIS POWER SUPPLY AND GROUND CIRCUIT COMBINATION METER COMBINATION METER : Diagnosis Procedure INFOID:0000000005383547 1.CHECK FUSE Check for blown fuses. Is the inspection result normal? YES >> GO TO 2. NO >> Be sure to eliminate cause of malfunction before installing new fuse. 2.CHECK POWER SUPPLY CIRCUIT Check voltage between combination meter harness connector and ground. Is the inspection result normal? YES >> GO TO 3. NO >> Check harness between combination meter and fuse. 3.CHECK GROUND CIRCUIT 1. Turn ignition switch OFF. 2. Disconnect combination meter connector. 3. Check continuity between combination meter harness connector and ground. Is the inspection result normal? YES >> INSPECTION END NO >> Repair harness or connector. UNIFIED METER AND A/C AMP. UNIFIED METER AND A/C AMP. : Diagnosis Procedure INFOID:0000000005383548 1.CHECK FUSE Check for blown fuses. Power source Fuse No. Battery 11 Ignition switch ON or START 4 Terminals (+) Ignition switch position Value (Approx.) (-) Combination meter Terminal Signal name M53 1 Battery power supply Ground OFF Battery voltage 21 Ignition signal ON Battery voltage Combination meter Ground Continuity Connector Terminal M53 5 Existed 15 Existed 22 Existed WCS POWER SUPPLY AND GROUND CIRCUIT WCS-25 < DTC/CIRCUIT DIAGNOSIS > C D E F G H I J K L M B A O P Is the inspection result normal? YES >> GO TO 2. NO >> Be sure to eliminate cause of malfunction before installing new fuse. 2.CHECK POWER SUPPLY CIRCUIT Check voltage between unified meter and A/C amp. harness connector and ground. Is the inspection result normal? YES >> GO TO 3. NO >> Check harness between unified meter and A/C amp. and fuse. 3.CHECK GROUND CIRCUIT 1. Turn ignition switch OFF. 2. Disconnect unified meter and A/C amp. connector. 3. Check continuity between unified meter and A/C amp. harness connector and ground. Is the inspection result normal? YES >> INSPECTION END NO >> Repair harness or connector. BCM (BODY CONTROL MODULE) BCM (BODY CONTROL MODULE) : Diagnosis Procedure INFOID:0000000005457394 1.CHECK FUSE AND FUSIBLE LINK Check that the following fuse and fusible link are not blown. Is the fuse fusing? YES >> Replace the blown fuse or fusible link after repairing the affected circuit if a fuse or fusible link is blown. NO >> GO TO 2. 2.CHECK POWER SUPPLY CIRCUIT 1. Turn ignition switch OFF. 2. Disconnect BCM connectors. Power source Fuse No. Battery 11 Ignition switch ACC or ON 19 Ignition switch ON or START 3 Terminals Ignition (+) switch position Value (Approx.) (-) Unified meter A/C amp. Terminal Signal name M67 54 Battery power supply Ground OFF Battery voltage 41 ACC power supply ACC Battery voltage 53 Ignition signal ON Battery voltage Unified meter A/C amp. Ground Continuity Connector Terminal M67 55 Existed 71 Existed Signal name Fuse and fusible link No. Battery power supply L 10 WCS-26 < DTC/CIRCUIT DIAGNOSIS > POWER SUPPLY AND GROUND CIRCUIT 3. Check voltage between BCM harness connector and ground. Is the measurement value normal? YES >> GO TO 3. NO >> Repair harness or connector. 3.CHECK GROUND CIRCUIT Check continuity between BCM harness connector and ground. Does continuity exist? YES >> INSPECTION END NO >> Repair harness or connector. Terminals Voltage (Approx.) (+) (−) BCM Ground Connector Terminal M118 1 Battery voltage M119 11 BCM Ground Continuity Connector Terminal M119 13 Existed WCS METER BUZZER CIRCUIT WCS-27 < DTC/CIRCUIT DIAGNOSIS > C D E F G H I J K L M B A O P METER BUZZER CIRCUIT Description INFOID:0000000004968271 • The buzzer for warning chime system is installed in the combination meter. • The combination meter sounds the alarm buzzer based on the signals transmitted from various units. Component Function Check INFOID:0000000004968272 1.CHECK OPERATION OF METER BUZZER 1. Select “BUZZER” of “BCM” on CONSULT-III. 2. Perform “LIGHT WARN ALM” of “ACTIVE TEST”. Does meter buzzer beep? YES >> INSPECTION END NO >> GO TO 2. 2.CHECK UNIFIED METER AND A/C AMP. INPUT SIGNAL Select the “Data Monitor” for the “METER/M&A” and check the “BUZZER” monitor value. Is the inspection result normal? YES >> Replace combination meter. NO >> Replace BCM. Refer to BCS-94, "Removal and Installation". Diagnosis Procedure INFOID:0000000004968273 1.CHECK POWER SUPPLY OF COMBINATION METER Check power supply of combination meter. Refer to MWI-59, "COMBINATION METER : Diagnosis Procedure". Is the inspection result normal? YES >> GO TO 2. NO >> Repair power supply circuit of combination meter. 2.CHECK POWER SUPPLY OF UNIFIED METER AND A/C AMP. Check power supply of unified meter and A/C amp. Refer to MWI-59, "UNIFIED METER AND A/C AMP. : Diagnosis Procedure". Is the inspection result normal? YES >> INSPECTION END NO >> Repair power supply circuit of unified meter and A/C amp. BUZZER Under the condition of buzzer input : On Except above : Off WCS-28 < DTC/CIRCUIT DIAGNOSIS > FRONT SEAT BELT BUCKLE SWITCH SIGNAL CIRCUIT (DRIVER SIDE) FRONT SEAT BELT BUCKLE SWITCH SIGNAL CIRCUIT (DRIVER SIDE) Description INFOID:0000000004968274 Transmits a seat belt buckle switch signal (driver side) to the unified meter and A/C amp. Component Function Check INFOID:0000000004968275 1.CHECK UNIFIED METER AND A/C AMP. INPUT SIGNAL Select the “Data Monitor” for the “METER/M&A” and check the “BUCKLE SW” monitor value. >> INSPECTION END Diagnosis Procedure INFOID:0000000004968276 1.CHECK SEAT BELT BUCKLE SWITCH (DRIVER SIDE) CIRCUIT 1. Turn ignition switch OFF. 2. Disconnect unified meter and A/C amp. connector and seat belt buckle switch (driver side) connector. 3. Check continuity between unified meter and A/C amp. harness connector and seat belt buckle switch (driver side) harness connector. *1: LHD models *2: RHD models 4. Check harness continuity between unified meter and A/C amp. harness connector and ground. Is the inspection result normal? YES >> GO TO 2. NO >> Repair harness or connector. 2.CHECK SEAT BELT BUCKLE SWITCH (DRIVER SIDE) GROUND CIRCUIT Check harness continuity between seat belt buckle switch (driver side) harness connector and ground. *1: LHD models *2: RHD models Is the inspection result normal? YES >> INSPECTION END NO >> Repair harness or connector. BUCKLE SW When driver seat belt is fastened : Off When driver seat belt is unfastened : On Unified meter and A/C amp. Seat belt buckle switch (driver side) Continuity Connector Terminal Connector Terminal M66 9 B503*1 61 Existed B591*2 Existed Unified meter and A/C amp. Ground Continuity Connector Terminal M66 9 Not existed Seat belt buckle switch (driver side) Ground Continuity Connector Terminal B503*1 60 Existed B591*2 Existed WCS FRONT SEAT BELT BUCKLE SWITCH SIGNAL CIRCUIT (DRIVER SIDE) WCS-29 < DTC/CIRCUIT DIAGNOSIS > C D E F G H I J K L M B A O P Component Inspection INFOID:0000000004968277 1.CHECK SEAT BELT BUCKLE SWITCH UNIT 1. Turn ignition switch OFF. 2. Disconnect the seat belt buckle switch (driver side) connector. 3. Check continuity between terminals. Is the inspection result normal? YES >> INSPECTION END NO >> Replace the seat belt buckle (driver side). Refer to SB-10, "SEAT BELT BUCKLE : Removal and Installation". Terminals Condition Continuity 61 - 60 When driver seat belt is fastened Not existed When driver seat belt is unfastened Existed WCS-30 < DTC/CIRCUIT DIAGNOSIS > FRONT SEAT BELT BUCKLE SWITCH SIGNAL CIRCUIT (PASSENGER SIDE) FRONT SEAT BELT BUCKLE SWITCH SIGNAL CIRCUIT (PASSENGER SIDE) Description INFOID:0000000004968278 Transmits a seat belt buckle switch signal (passenger side) to the unified meter and A/C amp. Diagnosis Procedure INFOID:0000000004968279 1.CHECK SEAT BELT BUCKLE SWITCH (PASSENGER SIDE) CIRCUIT 1. Turn ignition switch OFF. 2. Disconnect unified meter and A/C amp. connector and seat belt buckle switch (passenger side) connector. 3. Check continuity between unified meter and A/C amp. harness connector and seat belt buckle switch (passenger side) harness connector. *1: LHD models *2: RHD models 4. Check harness continuity between unified meter and A/C amp. harness connector and ground. Is the inspection result normal? YES >> GO TO 2. NO >> Repair harness or connector. 2.CHECK SEAT BELT BUCKLE SWITCH (PASSENGER SIDE) GROUND CIRCUIT Check harness continuity between seat belt buckle switch (passenger side) harness connector and ground. *1: LHD models *2: RHD models Is the inspection result normal? YES >> INSPECTION END NO >> Repair harness or connector. Component Inspection INFOID:0000000004968280 SEAT BELT BUCKLE SWITCH (PASSENGER SIDE) 1.CHECK SEAT BELT BUCKLE SWITCH (PASSENGER SIDE) UNIT 1. Turn ignition switch OFF. 2. Disconnect the seat belt buckle switch (passenger side) connectors. 3. Check continuity between terminals. Unified meter and A/C amp. Seat belt buckle switch (passenger side) Continuity Connector Terminal Connector Terminal M66 12 B513*1 61 Existed B626*2 Unified meter and A/C amp. Ground Continuity Connector Terminal M66 12 Not existed Seat belt buckle switch (passenger side) Ground Continuity Connector Terminal B513*1 60 Existed B626*2 WCS FRONT SEAT BELT BUCKLE SWITCH SIGNAL CIRCUIT (PASSENGER SIDE) WCS-31 < DTC/CIRCUIT DIAGNOSIS > C D E F G H I J K L M B A O P Is the inspection result normal? YES >> INSPECTION END NO >> Replace the seat belt buckle (passenger side). Refer to SB-10, "SEAT BELT BUCKLE : Removal and Installation". OCCUPANT DETECTION UNIT 1.CHECK OCCUPANT DETECTION UNIT 1. Turn ignition switch OFF. 2. Disconnect the occupant detection unit connector. 3. Check continuity between terminals. Is the inspection result normal? YES >> INSPECTION END NO >> Replace the occupant detection unit. Refer to SE-93, "Removal and Installation". Terminals Condition Continuity 61 - 3 When passenger seat belt is fastened Not existed When passenger seat belt is unfastened Existed 4 - 60 — Existed Terminal Condition Continuity 3 4 When getting in the passenger seat Existed Other than above Not existed WCS-32 < DTC/CIRCUIT DIAGNOSIS > WARNING CHIME SYSTEM WARNING CHIME SYSTEM Wiring Diagram - WARNING CHIME (LHD MODELS) - INFOID:0000000004968281 For connector terminal arrangements, harness layouts, and alphabets in a (option abbreviation; if not described in wiring diagram), refer to GI-12, "Connector Information". JCNWM4389GB WCS WARNING CHIME SYSTEM WCS-33 < DTC/CIRCUIT DIAGNOSIS > C D E F G H I J K L M B A O P JCNWM4390GB WCS-34 < DTC/CIRCUIT DIAGNOSIS > WARNING CHIME SYSTEM Wiring Diagram - WARNING CHIME (RHD MODELS) - INFOID:0000000004968282 For connector terminal arrangements, harness layouts, and alphabets in a (option abbreviation; if not described in wiring diagram), refer to GI-12, "Connector Information". JCNWM4391GB WCS WARNING CHIME SYSTEM WCS-35 < DTC/CIRCUIT DIAGNOSIS > C D E F G H I J K L M B A O P JCNWM4392GB WCS-36 < ECU DIAGNOSIS INFORMATION > COMBINATION METER ECU DIAGNOSIS INFORMATION COMBINATION METER Reference Value INFOID:0000000005383549 VALUES ON THE DIAGNOSIS TOOL Refer to WCS-54, "Reference Value". TERMINAL LAYOUT PHYSICAL VALUES JPNIA0968GB Terminal No. (Wire color) Description Condition Value (Approx.) + – Signal name Input/ Output 1 (O)*1 (GR)*2 Ground Battery power supply Input Ignition switch OFF — Battery voltage 2 (LG) Ground Communication signal (METER→ AMP.) Output Ignition switch ON — 3 (GR) Ground Communication signal (AMP.→ METER) Input Ignition switch ON — 5 (B) Ground Ground — Ignition switch ON — 0 V 6 (W) Ground Alternator signal Input Ignition switch ON Charge warning lamp ON 0 V Charge warning lamp OFF Battery voltage 7 (P)*1 (BR)*3 (W)*4 Ground Air bag signal Input Ignition switch ON Air bag warning lamp ON 4 V Air bag warning lamp OFF 0 V JSNIA0027GB JSNIA0027GB WCS COMBINATION METER WCS-37 < ECU DIAGNOSIS INFORMATION > C D E F G H I J K L M B A O P 10 (G) Ground Security indicator signal Input Ignition switch OFF Security warning lamp ON 0 V Security warning lamp OFF 12 V 11 (V) Ground Fuel filter sensor signal Input Ignition switch OFF Fuel filter warning lamp ON 0 V Fuel filter warning lamp OFF 12 V 15 (B) Ground Ground — Ignition switch ON — 0 V 16 (B) Ground Meter control switch ground — Ignition switch ON — 0 V 21 (R)*1 (W)*2 Ground Ignition power supply Input Ignition switch ON — Battery voltage 22 (B) Ground Ground — Ignition switch ON — 0 V 24 (P)*3 (BR)*5 Ground Communication signal (LCD→ AMP.) Output Ignition switch ON — 25 (Y) Ground Communication signal (AMP.→ LCD) Input Ignition switch ON — 26 (R) Ground Vehicle speed signal (8-pulse) Input Ignition switch ON Speedometer operated [When vehicle speed is approx. 40 km/h (25 MPH)] NOTE: The maximum voltage varies depending on the specification (destination unit). 27 (V) Ground Parking brake switch signal Input Ignition switch ON Parking brake ON 0 V Parking brake OFF Terminal No. (Wire color) Description Condition Value (Approx.) + – Signal name Input/ Output JSNIA0028GB JSNIA0027GB JSNIA0012GB JSNIA0007GB WCS-38 < ECU DIAGNOSIS INFORMATION > COMBINATION METER *1: LHD models with gasoline engine. *2: Except LHD models with gasoline engine. *3: LHD models with diesel engine. *4: RHD models. *5: Except LHD models with diesel engine. 28 (W) Ground Brake fluid level switch signal Input Ignition switch ON Brake fluid level is normal. 5 V The brake fluid level is lower than the low level 0 V 29 (SB) Ground Front seat belt buckle switch signal (driver side) Input Ignition switch ON When driver seat belt is fastened 12 V When driver seat belt is not fastened 0 V 30 (G) Ground Front seat belt buckle switch signal (passenger side) Input Ignition switch ON • When getting in the passenger seat • When passenger seat belt is fastened 12 V • When getting in the passenger seat • When passenger seat belt is not fastened 0 V 31 (L) Ground Washer level switch signal Input Ignition switch ON Washer level switch ON 0 V Washer level switch OFF 5 V 34 (O) Ground Illumination control signal Output Ignition switch ON Lighting switch ON, then operate the illumination control switch. NOTE: When brightness level is midway 36 (LG) 16 (B) Select switch signal Input Ignition switch ON When is pressed 0 V Other than the above 5 V 37 (SB) 16 (B) Enter switch signal Input Ignition switch ON When is pressed 0 V Other than the above 5 V 38 (L) 16 (B) Trip A/B reset switch signal Input Ignition switch ON When trip A/B reset switch is pressed 0 V Other than the above 5 V 39 (P) 16 (B) Illumination control switch signal (–) Input Ignition switch ON When switch is pressed 0 V Other than the above 5 V 40 (O) 16 (B) Illumination control switch signal (+) Input Ignition switch ON When switch is pressed 0 V Other than the above 5 V Terminal No. (Wire color) Description Condition Value (Approx.) + – Signal name Input/ Output JSNIA0010GB WCS COMBINATION METER WCS-39 < ECU DIAGNOSIS INFORMATION > C D E F G H I J K L M B A O P Wiring Diagram - METER (LHD MODELS WITH GASOLINE ENGINE) - INFOID:0000000005383550 For connector terminal arrangements, harness layouts, and alphabets in a (option abbreviation; if not described in wiring diagram), refer to GI-12, "Connector Information". JCNWM4375GB WCS-40 < ECU DIAGNOSIS INFORMATION > COMBINATION METER JCNWM4376GB WCS COMBINATION METER WCS-41 < ECU DIAGNOSIS INFORMATION > C D E F G H I J K L M B A O P JCNWM4377GB WCS-42 < ECU DIAGNOSIS INFORMATION > COMBINATION METER Wiring Diagram - METER (RHD MODELS WITH GASOLINE ENGINE) - INFOID:0000000005383551 For connector terminal arrangements, harness layouts, and alphabets in a (option abbreviation; if not described in wiring diagram), refer to GI-12, "Connector Information". JCNWM4378GB WCS COMBINATION METER WCS-43 < ECU DIAGNOSIS INFORMATION > C D E F G H I J K L M B A O P JCNWM4379GB WCS-44 < ECU DIAGNOSIS INFORMATION > COMBINATION METER JCNWM4380GB WCS COMBINATION METER WCS-45 < ECU DIAGNOSIS INFORMATION > C D E F G H I J K L M B A O P Wiring Diagram - METER (LHD MODELS WITH DIESEL ENGINE) - INFOID:0000000006113600 For connector terminal arrangements, harness layouts, and alphabets in a (option abbreviation; if not described in wiring diagram), refer to GI-12, "Connector Information". JCNWM4381GB WCS-46 < ECU DIAGNOSIS INFORMATION > COMBINATION METER JCNWM4382GB WCS COMBINATION METER WCS-47 < ECU DIAGNOSIS INFORMATION > C D E F G H I J K L M B A O P JCNWM4383GB WCS-48 < ECU DIAGNOSIS INFORMATION > COMBINATION METER JCNWM4384GB WCS COMBINATION METER WCS-49 < ECU DIAGNOSIS INFORMATION > C D E F G H I J K L M B A O P Wiring Diagram - METER (RHD MODELS WITH DIESEL ENGINE) - INFOID:0000000006113601 For connector terminal arrangements, harness layouts, and alphabets in a (option abbreviation; if not described in wiring diagram), refer to GI-12, "Connector Information". JCNWM4385GB WCS-50 < ECU DIAGNOSIS INFORMATION > COMBINATION METER JCNWM4386GB WCS COMBINATION METER < ECU DIAGNOSIS INFORMATION > C D E F G H I J K L M B A O P JCNWM4387GB WCS-52 < ECU DIAGNOSIS INFORMATION > COMBINATION METER Fail-safe INFOID:0000000005383552 FAIL-SAFE Combination meter performs fail-safe operation when unified meter and A/C amp. communication is malfunction. Solution for communication error between the unified meter and A/C amp. and combination meter. JCNWM4388GB WCS COMBINATION METER WCS-53 < ECU DIAGNOSIS INFORMATION > C D E F G H I J K L M B A O P DTC Index INFOID:0000000005383553 Refer to WCS-76, "DTC Index". Function Specifications Speedometer Reset to zero by suspending communication. Tachometer Fuel gauge Engine coolant temperature gauge Illumination control When suspending communication, change to nighttime mode. Information display The display turns off by suspending communication. Buzzer The buzzer turns off by suspending communication. Warning lamp/indicator lamp ABS warning lamp The lamp turns on by suspending communication. ESP OFF indicator lamp SLIP indicator lamp Brake warning lamp RAS warning lamp CRUISE warning lamp IBA warning lamp High beam indicator The lamp turns off by suspending communication. Turn signal indicator lamp Tail lamp indicator lamp Oil pressure warning lamp Malfunction indicator lamp A/T CHECK warning lamp 4WD warning lamp Low tire pressure warning lamp Key warning lamp AFS OFF indicator lamp Sports mode indicator lamp Master warning lamp Glow indicator lamp Front fog indicator lamp Rear fog indicator lamp WCS-54 < ECU DIAGNOSIS INFORMATION > UNIFIED METER AND A/C AMP. UNIFIED METER AND A/C AMP. Reference Value INFOID:0000000005383554 VALUES ON THE DIAGNOSIS TOOL CONSULT-III MONITOR ITEM Monitor Item Condition Value/Status SPEED METER [km/h] or [mph] Ignition switch ON While driving Equivalent to speedometer reading NOTE: 655.35 is displayed when the malfunction signal is received SPEED OUTPUT [km/h] or [mph] Ignition switch ON While driving Equivalent to speedometer reading NOTE: 655.35 is displayed when the malfunction signal is received ODO OUTPUT [km/h] Ignition switch ON — Equivalent to odometer reading in combination meter TACHO METER [rpm] Ignition switch ON While driving Equivalent to tachometer reading NOTE: 8191.875 is displayed when the malfunction signal is received FUEL METER [L] Ignition switch ON — Values according to fuel level W TEMP METER [°C] or [°F] Ignition switch ON — Values according to engine coolant temperature NOTE: 215 is displayed when the malfunction signal is input ABS W/L Ignition switch ON ABS warning lamp ON On ABS warning lamp OFF Off VDC/TCS IND Ignition switch ON ESP OFF indicator lamp ON On ESP OFF indicator lamp OFF Off SLIP IND Ignition switch ON SLIP indicator lamp ON On SLIP indicator lamp OFF Off BRAKE W/L Ignition switch ON Brake warning lamp ON On Brake warning lamp OFF Off DOOR W/L Ignition switch ON Door warning displayed On Door warning not displayed Off HI-BEAM IND Ignition switch ON Hi-beam indicator lamp ON On Hi-beam indicator lamp OFF Off TURN IND Ignition switch ON Turn indicator lamp ON On Turn indicator lamp OFF Off FR FOG IND Ignition switch ON Front fog indicator lamp ON On Front fog indicator lamp OFF Off RR FOG IND Ignition switch ON Rear fog indicator lamp ON On Rear fog indicator lamp OFF Off LIGHT IND Ignition switch ON Tail lamp indicator lamp ON On Tail lamp indicator lamp OFF Off OIL W/L Ignition switch ON Oil pressure warning lamp ON On Oil pressure warning lamp OFF Off WCS UNIFIED METER AND A/C AMP. WCS-55 < ECU DIAGNOSIS INFORMATION > C D E F G H I J K L M B A O P MIL Ignition switch ON Malfunction warning lamp ON On Malfunction warning lamp OFF Off GLOW IND Ignition switch ON Glow indicator lamp ON On Glow indicator lamp OFF Off C-ENG2 W/L Ignition switch ON NOTE: This item is displayed, but cannot be monitored. Off CRUISE IND Ignition switch ON CRUISE indicator displayed On CRUISE indicator not displayed Off SET IND Ignition switch ON SET indicator displayed ON On SET indicator not displayed OFF Off CRUISE W/L Ignition switch ON CRUISE warning lamp ON On CRUISE warning lamp OFF Off BA W/L Ignition switch ON IBA OFF indicator lamp ON On IBA OFF indicator lamp OFF Off ATC/T-AMT W/L Ignition switch ON A/T check warning lamp ON On A/T check warning lamp OFF Off 4WD W/L Ignition switch ON 4WD warning lamp ON On 4WD warning lamp OFF Off 4WD LOCK IND Ignition switch ON NOTE: This item is displayed, but cannot be monitored. Off FUEL W/L Ignition switch ON Low-fuel warning displayed On Low-fuel warning not displayed Off WASHER W/L Ignition switch ON Washer warning displayed On Washer warning not displayed Off AIR PRES W/L Ignition switch ON Low tire pressure lamp ON On Low tire pressure lamp OFF Off KEY G/Y W/L Ignition switch ON Key warning lamp ON On Key warning lamp OFF Off AFS OFF IND Ignition switch ON AFS OFF indicator lamp ON On AFS OFF indicator lamp OFF Off 4WAS/RAS W/L Ignition switch ON RAS warning lamp ON On RAS warning lamp OFF Off HDC W/L Ignition switch ON NOTE: This item is displayed, but cannot be monitored. Off LANE W/L Ignition switch ON Lane departure warning lamp ON On Lane departure warning lamp OFF Off LDP IND Ignition switch ON LDP ON indicator lamp ON On LDP ON indicator lamp OFF Off E-SUS IND Ignition switch ON Sports mode indicator lamp ON On Sports mode indicator lamp OFF Off DCA IND Ignition switch ON DCA switch indicator displayed On DCA switch indicator not displayed Off Monitor Item Condition Value/Status WCS-56 < ECU DIAGNOSIS INFORMATION > UNIFIED METER AND A/C AMP. LCD Ignition switch ON Engine start information display B&P I Ignition switch ACC Engine start information display B&P N Ignition switch LOCK Key ID warning display ID NG Ignition switch LOCK Steering lock information display ROTAT Ignition switch LOCK P position warning display SFT P Ignition switch LOCK Intelligent Key insert information display INSRT Ignition switch LOCK Intelligent Key low battery warning display BATT Ignition switch ON Take away warning display NO KY Ignition switch LOCK Key warning display OUTKY Ignition switch ON ACC warning display LK WN ACC TARGET Ignition switch ON Vehicle ahead detection indicator displayed On Vehicle ahead detection indicator not displayed Off ACC DISTANCE Ignition switch ON When following distance set to “LONG” Long When following distance set to “MIDDLE” Middle When following distance set to “SHORT” Short Set distance indicator not displayed Off ACC OWN VHL Ignition switch ON Own vehicle indicator displayed On Own vehicle indicator not displayed Off ACC SET SPEED Ignition switch ON Set vehicle speed indicator not displayed Off Set vehicle speed indicator displayed Indicates the set vehicle speed ACC UNIT Ignition switch ON Set vehicle speed indicator unit display ON On Set vehicle speed indicator unit display OFF Off SHIFT IND Ignition switch ON Shift position indicator P display P Shift position indicator R display R Shift position indicator N display N Shift position indicator D display D Shift position indicator DS display L Shift position indicator M1 display M1 Shift position indicator M2 display M2 Shift position indicator M3 display M3 Shift position indicator M4 display M4 Shift position indicator M5 display M5 Shift position indicator M6 display M6 Shift position indicator M7 display M7 O/D OFF SW Ignition switch ON NOTE: This item is displayed, but cannot be monitored. Off Monitor Item Condition Value/Status WCS UNIFIED METER AND A/C AMP. WCS-57 < ECU DIAGNOSIS INFORMATION > C D E F G H I J K L M B A O P AT S MODE SW Ignition switch ON Snow mode switch pressed On Snow mode switch not pressed Off AT P MODE SW Ignition switch ON NOTE: This item is displayed, but cannot be monitored. Off M RANGE SW Ignition switch ON Selector lever manual mode position On Other than the above Off NM RANGE SW Ignition switch ON Selector lever manual mode position Off Other than the above On AT SFT UP SW Ignition switch ON Selector lever + position On Other than the above Off AT SFT DWN SW Ignition switch ON Selector lever – position On Other than the above Off ST SFT UP SW Ignition switch ON Paddle shifter switch up operation On Other than the above Off ST SFT DWN SW Ignition switch ON Paddle shifter switch down operation On Other than the above Off COMP F/B SIG Ignition switch ON A/C compressor activation condition On A/C compressor deactivation condition Off 4WD LOCK SW Ignition switch ON NOTE: This item is displayed, but cannot be monitored. Off PKB SW Ignition switch ON Parking brake switch ON On Parking brake switch OFF Off BUCKLE SW Ignition switch ON Driver seat belt not fastened On Driver seat belt fastened Off BRAKE OIL SW Ignition switch ON Brake fluid level switch ON On Brake fluid level switch OFF Off DISTANCE [km/h] Ignition switch ON — Possible driving distance calculated by unified meter and A/C amp. OUTSIDE TEMP [°C] or [°F] Ignition switch ON — Equivalent to ambient temperature NOTE: This may not match the indicated value on the information display. FUEL LOW SIG Ignition switch ON Low-fuel warning signal output On Low-fuel warning signal not output Off CRANKING SIG Ignition switch ON On At engine cranking Off ST CNT SIG Ignition switch ON On At engine cranking Off DOOR LOCK SIG Ignition switch ON NOTE: This item is displayed, but cannot be monitored. Off DR DOOR SIG Ignition switch ON NOTE: This item is displayed, but cannot be monitored. Off BUZZER Ignition switch ON Buzzer ON On Buzzer OFF Off Monitor Item Condition Value/Status WCS-58 < ECU DIAGNOSIS INFORMATION > UNIFIED METER AND A/C AMP. NOTE: Some items are not available according to vehicle specification. TERMINAL LAYOUT PHYSICAL VALUES ASCD REQ SPD Ignition switch ON While driving Same value as ASCD or speed limiter set vehicle speed ASCD STATUS Ignition switch ON ASCD and speed limiter system OFF Off ASCD system ON ASCD ASCD set vehicle speed CRUISE Speed limiter system ON SL ON Speed limiter set vehicle speed SL SET ASCD SPD BLNK Ignition switch ON Set vehicle speed indicator blinking On Set vehicle speed indicator not blinking Off Monitor Item Condition Value/Status JSNIA0097ZZ Terminal No. (Wire color) Description Condition Value (Approx.) + – Signal name Input/ Output 5 (L) Ground Manual mode shift up signal Input Ignition switch ON Selector lever UP operation 0 V Other than the above 12 V 6 (O) Ground Paddle shifter up signal Input Ignition switch ON Paddle shifter up operation 0 V Other than the above 12 V 7 (GR) Ground Communication signal (AMP. → METER) Output Ignition switch ON — 8 (L) Ground Vehicle speed signal (2-pulse) Output Ignition switch ON Speedometer operated [When vehicle speed is approx. 40 km/h (25 MPH)] NOTE: The maximum voltage varies depending on the specification (destination unit). JSNIA0027GB JSNIA0015GB WCS UNIFIED METER AND A/C AMP. WCS-59 < ECU DIAGNOSIS INFORMATION > C D E F G H I J K L M B A O P 9 (SB) Ground Front seat belt buckle switch signal (driver side) Input Ignition switch ON When driver seat belt is fastened When driver seat belt is not fastened 0 V 10 (W) Ground Manual mode signal Input Ignition switch ON Selector lever DS position 0 V Other than the above 12 V 11 (G) Ground Non-manual mode signal Input Ignition switch ON Selector lever DS position 12 V Other than the above 0 V 12 (LG)*1 (G)*2 Ground Front seat belt buckle switch signal (passenger side) Input Ignition switch ON • When getting in the passenger seat • When passenger seat belt is fastened 12 V • When getting in the passenger seat • When passenger seat belt is not fastened 0 V 13 (SB)*3 (V)*4 Ground Rear seat belt buckle switch signal (center) Input Ignition switch ON When seat belt is fastened 12 V When seat belt is not fastened 0 V 14 (BR)*5 (P)*6 Ground Communication signal (LCD → AMP.) Input Ignition switch ON — 25 (V) Ground Manual mode shift down signal Input Ignition switch ON Selector lever down operation 0 V Other than the above 12 V 26 (G) Ground Paddle shifter down signal Input Ignition switch ON Paddle shifter down operation 0 V Other than the above 12 V 27 (LG) Ground Communication signal (METER → AMP.) Input Ignition switch ON — Terminal No. (Wire color) Description Condition Value (Approx.) + – Signal name Input/ Output JPNIA1177ZZ JSNIA0028GB JSNIA0027GB WCS-60 < ECU DIAGNOSIS INFORMATION > UNIFIED METER AND A/C AMP. 28 (R) Ground Vehicle speed signal (8-pulse) Output Ignition switch ON Speedometer operated [When vehicle speed is approx. 40 km/h (25 MPH)] NOTE: The maximum voltage varies depending on the specification (destination unit). 30 (V) Ground Parking brake switch signal Input Ignition switch ON Parking brake ON 0 V Parking brake OFF 32 (P) Ground Rear seat belt buckle switch signal (LH) Input Ignition switch ON When seat belt is fastened 12 V When seat belt is not fastened 0 V 33 (L)*3 (R)*4 Ground Rear seat belt buckle switch signal (RH) Input Ignition switch ON When seat belt is fastened 12 V When seat belt is not fastened 0 V 34 (Y) Ground Communication signal (AMP. → LCD) Output Ignition switch ON — 41 (V) Ground ACC power supply Input Ignition switch ACC — Battery voltage 42 (GR)*6 (Y)*5 Ground Fuel level sensor signal Input Ignition switch ON — 45 (P) Ground Ambient sensor signal Input — — Terminal No. (Wire color) Description Condition Value (Approx.) + – Signal name Input/ Output JSNIA0012GB JSNIA0007GB JSNIA0027GB SKIB8867E JSNIA0014GB WCS UNIFIED METER AND A/C AMP. WCS-61 < ECU DIAGNOSIS INFORMATION > C D E F G H I J K L M B A O P *1: LHD models with gasoline engine. *2: Except LHD models with gasoline engine. *3: LHD models. *4: RHD models. *5: Except LHD models with diesel engine. *6: LHD models with diesel engine. 50 (P) Ground Oil level sensor signal Input Ignition switch ON — Refer to MWI-58, "Component Inspection". NOTE: The measurement cannot be performed because the signal is input for a moment with the ignition switch ON. 51 (BR) Ground Oil level sensor signal ground — Ignition switch ON — 0 V 53 (W)*6 (G)*5 Ground Ignition power supply Input Ignition switch ON — Battery voltage 54 (O)*1 (Y)*2 Ground Battery power supply Input Ignition switch OFF — Battery voltage 55 (B) Ground Ground — Ignition switch ON — 0 V 56 (L) Ground CAN-H — — — — 57 (W) Ground Brake fluid level switch signal Input Ignition switch ON Brake fluid level is normal. 5 V The brake fluid level is lower than the low level 0 V 58 (BR)*6 (B)*5 Ground Fuel level sensor signal ground — Ignition switch ON — 0 V 61 (R)*6 (BR)*5 Ground Ambient sensor signal ground — Ignition switch ON — 0 V 71 (B) Ground Ground — Ignition switch ON — 0 V 72 (P) Ground CAN-L — — — — Terminal No. (Wire color) Description Condition Value (Approx.) + – Signal name Input/ Output WCS-62 < ECU DIAGNOSIS INFORMATION > UNIFIED METER AND A/C AMP. Wiring Diagram - METER (LHD MODELS WITH GASOLINE ENGINE) - INFOID:0000000005457405 For connector terminal arrangements, harness layouts, and alphabets in a (option abbreviation; if not described in wiring diagram), refer to GI-12, "Connector Information". JCNWM4375GB WCS UNIFIED METER AND A/C AMP. WCS-63 < ECU DIAGNOSIS INFORMATION > C D E F G H I J K L M B A O P JCNWM4376GB WCS-64 < ECU DIAGNOSIS INFORMATION > UNIFIED METER AND A/C AMP. JCNWM4377GB WCS UNIFIED METER AND A/C AMP. WCS-65 < ECU DIAGNOSIS INFORMATION > C D E F G H I J K L M B A O P Wiring Diagram - METER (RHD MODELS WITH GASOLINE ENGINE) - INFOID:0000000005457406 For connector terminal arrangements, harness layouts, and alphabets in a (option abbreviation; if not described in wiring diagram), refer to GI-12, "Connector Information". JCNWM4378GB WCS-66 < ECU DIAGNOSIS INFORMATION > UNIFIED METER AND A/C AMP. JCNWM4379GB WCS UNIFIED METER AND A/C AMP. WCS-67 < ECU DIAGNOSIS INFORMATION > C D E F G H I J K L M B A O P JCNWM4380GB WCS-68 < ECU DIAGNOSIS INFORMATION > UNIFIED METER AND A/C AMP. Wiring Diagram - METER (LHD MODELS WITH DIESEL ENGINE) - INFOID:0000000006113602 For connector terminal arrangements, harness layouts, and alphabets in a (option abbreviation; if not described in wiring diagram), refer to GI-12, "Connector Information". JCNWM4381GB WCS UNIFIED METER AND A/C AMP. WCS-69 < ECU DIAGNOSIS INFORMATION > C D E F G H I J K L M B A O P JCNWM4382GB WCS-70 < ECU DIAGNOSIS INFORMATION > UNIFIED METER AND A/C AMP. JCNWM4383GB WCS UNIFIED METER AND A/C AMP. WCS-71 < ECU DIAGNOSIS INFORMATION > C D E F G H I J K L M B A O P JCNWM4384GB WCS-72 < ECU DIAGNOSIS INFORMATION > UNIFIED METER AND A/C AMP. Wiring Diagram - METER (RHD MODELS WITH DIESEL ENGINE) - INFOID:0000000006113603 For connector terminal arrangements, harness layouts, and alphabets in a (option abbreviation; if not described in wiring diagram), refer to GI-12, "Connector Information". JCNWM4385GB WCS UNIFIED METER AND A/C AMP. WCS-73 < ECU DIAGNOSIS INFORMATION > C D E F G H I J K L M B A O P JCNWM4386GB WCS-74 < ECU DIAGNOSIS INFORMATION > UNIFIED METER AND A/C AMP. JCNWM4387GB WCS UNIFIED METER AND A/C AMP. WCS-75 < ECU DIAGNOSIS INFORMATION > C D E F G H I J K L M B A O Fail-safe P INFOID:0000000005383557 FAIL-SAFE The unified meter and A/C amp. activates the fail-safe control if CAN communication with each unit is malfunctioning. JCNWM4388GB WCS-76 < ECU DIAGNOSIS INFORMATION > UNIFIED METER AND A/C AMP. DTC Index INFOID:0000000005383558 Function Specifications Speedometer Reset to zero by suspending communication. Tachometer Fuel gauge Engine coolant temperature gauge Illumination control When suspending communication, change to nighttime mode. Information display The display turns off by suspending communication. Buzzer The buzzer turns off by suspending communication. Warning lamp/indicator lamp ABS warning lamp The lamp turns on by suspending communication. ESP OFF indicator lamp SLIP indicator lamp Brake warning lamp CRUISE warning lamp IBA warning lamp 4WD warning lamp Low tire pressure warning lamp RAS warning lamp Master warning lamp Malfunction indicator lamp AFS OFF indicator lamp The lamp blinking caused by communication malfunction High beam indicator The lamp turns off by suspending communication. Turn signal indicator lamp Tail lamp indicator lamp Oil pressure warning lamp Glow indicator lamp A/T CHECK warning lamp Key warning lamp Sports mode indicator lamp Front fog indicator lamp Rear fog indicator lamp Display contents of CONSULT- III Time Diagnostic item is detected when ... Refer to CAN COMM CIRCUIT [u] CRNT, 1 - 39 When unified meter and A/C amp. is not transmitting or receiving CAN communication signal for 2 seconds or more. MWI-48 CONTROL UNIT (CAN) [u] CRNT, 1 - 39 When detecting error during the initial diagnosis of CAN controller of unified meter and A/C amp. MWI-49 COMM ERROR 1 [b] CRNT, 1 - 39 If a communication error is present in the communication line between unified meter and A/C amp. and combination meter for 2 seconds or more. MWI-50 COMM ERROR 2 [b] CRNT, 1 - 39 If a communication error is present in the communication line between unified meter and A/C amp. and combination meter for 2 seconds or more. MWI-52 VEHICLE SPEED [b] CRNT, 1 - 39 The abnormal vehicle speed signal is input from ABS actuator and electric unit (control unit) for 2 seconds or more. MWI-54 WCS UNIFIED METER AND A/C AMP. WCS-77 < ECU DIAGNOSIS INFORMATION > C D E F G H I J K L M B A O P ENGINE SPEED [b] CRNT, 1 - 39 If ECM continuously transmits abnormal engine speed signals for 2 seconds or more. MWI-55 WATER TEMP [b] CRNT, 1 - 39 If ECM continuously transmits abnormal engine coolant temperature signals for 60 seconds or more. MWI-56 OIL LEV SEN OPEN [b] CRNT, 1 - 39 Signal from engine oil temperature/level sensor is open (resistance value of engine oil temperature/level sensor is larger than 20 Ω). MWI-57 OIL LEV SEN SHORT [b] CRNT, 1 - 39 Signal from engine oil temperature/level sensor is shorted (resistance value of engine oil temperature/level sensor is smaller than 3 Ω). MWI-57 Display contents of CONSULT- III Time Diagnostic item is detected when ... Refer to WCS-78 < ECU DIAGNOSIS INFORMATION > BCM (BODY CONTROL MODULE) BCM (BODY CONTROL MODULE) Reference Value INFOID:0000000005457388 VALUES ON THE DIAGNOSIS TOOL CONSULT-III MONITOR ITEM Monitor Item Condition Value/Status FR WIPER HI Other than front wiper switch HI Off Front wiper switch HI On FR WIPER LOW Other than front wiper switch LO Off Front wiper switch LO On FR WASHER SW Front washer switch OFF Off Front washer switch ON On FR WIPER INT Other than front wiper switch AUTO Off Front wiper switch AUTO On FR WIPER STOP Front wiper is not in STOP position Off Front wiper is in STOP position On INT VOLUME Wiper volume dial is in a dial position 1 - 7 Wiper volume dial position RR WIPER ON Other than rear wiper switch ON Off Rear wiper switch ON On RR WIPER INT Other than rear wiper switch INT Off Rear wiper switch INT On RR WASHER SW Rear washer switch OFF Off Rear washer switch ON On RR WIPER STOP Rear wiper is in STOP position Off Rear wiper is not in STOP position On TURN SIGNAL R Other than turn signal switch RH Off Turn signal switch RH On TURN SIGNAL L Other than turn signal switch LH Off Turn signal switch LH On TAIL LAMP SW Other than lighting switch 1ST and 2ND Off Lighting switch 1ST or 2ND On HI BEAM SW Other than lighting switch HI Off Lighting switch HI On HEAD LAMP SW 1 Other than lighting switch 2ND Off Lighting switch 2ND On HEAD LAMP SW 2 Other than lighting switch 2ND Off Lighting switch 2ND On PASSING SW Other than lighting switch PASS Off Lighting switch PASS On AUTO LIGHT SW Other than lighting switch AUTO Off Lighting switch AUTO On FR FOG SW Front fog lamp switch OFF Off Front fog lamp switch ON On WCS BCM (BODY CONTROL MODULE) WCS-79 < ECU DIAGNOSIS INFORMATION > C D E F G H I J K L M B A O P RR FOG SW Rear fog lamp switch OFF Off Rear fog lamp switch ON On DOOR SW-DR Driver door closed Off Driver door opened On DOOR SW-AS Passenger door closed Off Passenger door opened On DOOR SW-RR Rear RH door closed Off Rear RH door opened On DOOR SW-RL Rear LH door closed Off Rear LH door opened On DOOR SW-BK Back door closed Off Back door opened On CDL LOCK SW Other than power door lock switch LOCK Off Power door lock switch LOCK On CDL UNLOCK SW Other than power door lock switch UNLOCK Off Power door lock switch UNLOCK On KEY CYL LK-SW NOTE: The item is indicated, but not monitored. Off KEY CYL UN-SW NOTE: The item is indicated, but not monitored. Off KEY CYL SW-TR NOTE: The item is indicated, but not monitored. Off HAZARD SW Hazard switch is OFF Off Hazard switch is ON On REAR DEF SW NOTE: The item is indicated, but not monitored. Off H/L WASH SW NOTE: For models without headlamp washer switch, this item is not monitored. Headlamp washer switch is not pressed Off Headlamp washer switch is pressed On TR CANCEL SW NOTE: The item is indicated, but not monitored. Off TR/BD OPEN SW Back door opener switch OFF Off While the back door opener switch is turned ON On TRNK/HAT MNTR NOTE: The item is indicated, but not monitored. Off SEN CANCEL SW Sensor cancel switch is not pressed Off Sensor cancel switch is pressed On RKE-LOCK LOCK button of the Intelligent Key is not pressed Off LOCK button of the Intelligent Key is pressed On RKE-UNLOCK UNLOCK button of the Intelligent Key is not pressed Off UNLOCK button of the Intelligent Key is pressed On RKE-TR/BD NOTE: The item is indicated, but not monitored. Off RKE-PANIC NOTE: The item is indicated, but not monitored. Off Monitor Item Condition Value/Status WCS-80 < ECU DIAGNOSIS INFORMATION > BCM (BODY CONTROL MODULE) RKE-P/W OPEN UNLOCK button of the Intelligent Key is not pressed Off UNLOCK button of the Intelligent Key is pressed and held On RKE-MODE CHG LOCK/UNLOCK button of the Intelligent Key is not pressed and held simultaneously Off LOCK/UNLOCK button of the Intelligent Key is pressed and held simultaneously On OPTICAL SENSOR NOTE: For models without optical sensor, this item is not monitored. Bright outside of the vehicle Close to 5 V Dark outside of the vehicle Close to 0 V REQ SW -DR Driver door request switch is not pressed Off Driver door request switch is pressed On REQ SW -AS Passenger door request switch is not pressed Off Passenger door request switch is pressed On REQ SW -RR NOTE: The item is indicated, but not monitored. Off REQ SW -RL NOTE: The item is indicated, but not monitored. Off REQ SW -BD/TR Back door opener request switch is not pressed Off Back door opener request switch is pressed On PUSH SW Push-button ignition switch (push switch) is not pressed Off Push-button ignition switch (push switch) is pressed On IGN RLY2 -F/B Ignition switch in OFF or ACC position Off Ignition switch in ON position On ACC RLY -F/B NOTE: The item is indicated, but not monitored. Off CLUCH SW The clutch pedal is not depressed Off The clutch pedal is depressed On BRAKE SW 1 Brake pedal is depressed when No. 7 fuse is blown Off Brake pedal is not depressed when No. 7 fuse is blown, or No. 7 fuse is normal On BRAKE SW 2 Brake pedal is not depressed Off Brake pedal is depressed On DETE/CANCL SW Selector lever in P position Off Selector lever in any position other than P On SFT PN/N SW • Selector lever in any position other than P and N (A/T models) • Control lever in any position other than neutral (M/T models) Off • Selector lever in P or N position (A/T models) • Control lever in neutral position (M/T models) On S/L -LOCK Steering is unlocked Off Steering is locked On S/L -UNLOCK Steering is locked Off Steering is unlocked On S/L RELAY-F/B Ignition switch in OFF or ACC position Off Ignition switch in ON position On UNLK SEN -DR Driver door is unlocked Off Driver door is locked On PUSH SW -IPDM Push-button ignition switch (push-switch) is not pressed Off Push-button ignition switch (push-switch) is pressed On Monitor Item Condition Value/Status WCS BCM (BODY CONTROL MODULE) WCS-81 < ECU DIAGNOSIS INFORMATION > C D E F G H I J K L M B A O P IGN RLY1 -F/B Ignition switch in OFF or ACC position Off Ignition switch in ON position On DETE SW -IPDM Selector lever in any position other than P Off Selector lever in P position On SFT PN -IPDM Selector lever in any position other than P and N Off Selector lever in P or N position On SFT P -MET Selector lever in any position other than P Off Selector lever in P position On SFT N -MET Selector lever in any position other than N Off Selector lever in N position On ENGINE STATE Engine stopped Stop While the engine stalls Stall At engine cranking Crank Engine running Run S/L LOCK-IPDM Steering is unlocked Off Steering is locked On S/L UNLK-IPDM Steering is locked Off Steering is unlocked On S/L RELAY-REQ Steering lock system is not the LOCK condition and the changing condition from LOCK to UNLOCK Off Steering lock system is the LOCK condition or the changing condition from LOCK to UNLOCK On VEH SPEED 1 While driving Equivalent to speedometer reading VEH SPEED 2 While driving Equivalent to speedometer reading DOOR STAT-DR Driver door is locked LOCK Wait with selective UNLOCK operation (5 seconds) READY Driver door is unlocked UNLOCK DOOR STAT-AS Passenger door is locked LOCK Wait with selective UNLOCK operation (5 seconds) READY Passenger door is unlocked UNLOCK ID OK FLAG Steering is locked Reset Steering is unlocked Set PRMT ENG STRT The engine start is prohibited Reset The engine start is permitted Set PRMT RKE STRT NOTE: The item is indicated, but not monitored. Reset KEY SW -SLOT The Intelligent Key is not inserted into key slot Off The Intelligent Key is inserted into key slot On RKE OPE COUN1 During the operation of the Intelligent Key Operation frequency of the Intelligent Key RKE OPE COUN2 NOTE: The item is indicated, but not monitored. — REVERSE SW NOTE: For A/T models, this item is not monitored. Control lever in any position other than reverse position Off Control lever in reverse position On Monitor Item Condition Value/Status WCS-82 < ECU DIAGNOSIS INFORMATION > BCM (BODY CONTROL MODULE) CONFRM ID ALL The key ID that the key slot receives is not recognized by any key ID registered to BCM. Yet The key ID that the key slot receives accords with any key ID registered to BCM. Done CONFIRM ID4 The key ID that the key slot receives is not recognized by the fourth key ID registered to BCM. Yet The key ID that the key slot receives is recognized by the fourth key ID registered to BCM. Done CONFIRM ID3 The key ID that the key slot receives is not recognized by the third key ID registered to BCM. Yet The key ID that the key slot receives is recognized by the third key ID registered to BCM. Done CONFIRM ID2 The key ID that the key slot receives is not recognized by the second key ID registered to BCM. Yet The key ID that the key slot receives is recognized by the second key ID registered to BCM. Done CONFIRM ID1 The key ID that the key slot receives is not recognized by the first key ID registered to BCM. Yet The key ID that the key slot receives is recognized by the first key ID registered to BCM. Done TP 4 The ID of fourth Intelligent Key is not registered to BCM Yet The ID of fourth Intelligent Key is registered to BCM Done TP 3 The ID of third Intelligent Key is not registered to BCM Yet The ID of third Intelligent Key is registered to BCM Done TP 2 The ID of second Intelligent Key is not registered to BCM Yet The ID of second Intelligent Key is registered to BCM Done TP 1 The ID of first Intelligent Key is not registered to BCM Yet The ID of first Intelligent Key is registered to BCM Done Monitor Item Condition Value/Status WCS BCM (BODY CONTROL MODULE) WCS-83 < ECU DIAGNOSIS INFORMATION > C D E F G H I J K L M B A O P TERMINAL LAYOUT PHYSICAL VALUES JPMIA0062ZZ WCS-84 < ECU DIAGNOSIS INFORMATION > BCM (BODY CONTROL MODULE) Terminal No. (Wire color) Description Condition Value Signal name (Approx.) Input/ + – Output 1 (W) Ground Battery power supply Input Ignition switch OFF Battery voltage 3 (O)*2 (Y)*3 Ground P/W power supply (RAP) Output Ignition switch ON 12 V 4 (P) Ground Interior room lamp power supply (Battery saver signal) Output Interior room lamp battery saver is activated. (Cuts the interior room lamp power supply) 0 V Interior room lamp battery saver is not activated. (Outputs the interior room lamp power supply) 12 V 5*1 (G) Ground Super lock Output Super lock actuator Actuator is activated 12 V Actuator is not activated 0 V 7 (Y) Ground Step lamp Output Step lamp ON 0 V OFF 12 V 8 (V) Ground All doors, fuel lid LOCK Output All doors, fuel lid LOCK (Actuator is activated) 12 V Other than LOCK (Actuator is not activated) 0 V 9 (G) Ground Driver door, fuel lid UNLOCK Output Driver door, fuel lid UNLOCK (Actuator is activated) 12 V Other than UNLOCK (Actuator is not activated) 0 V 10 (BR) Ground Passenger door, rear RH door and rear LH door UNLOCK Output Passenger door, rear RH door and rear LH door UNLOCK (Actuator is activated) 12 V Other than UNLOCK (Actuator is not activated) 0 V 11 (R) Ground Battery power supply Input Ignition switch OFF Battery voltage 13 (B) Ground Ground — Ignition switch ON 0 V 15 (Y) Ground ACC indicator lamp Output Ignition switch OFF (LOCK indicator is not illuminated) Battery voltage ACC or ON 0 V 17 (W) Ground Turn signal RH (Front and side) Output Ignition switch ON Turn signal switch OFF 0 V Turn signal switch RH 6.5 V PKID0926E WCS BCM (BODY CONTROL MODULE) WCS-85 < ECU DIAGNOSIS INFORMATION > C D E F G H I J K L M B A O P 18 (O) Ground Turn signal LH (Front and side) Output Ignition switch ON Turn signal switch OFF 0 V Turn signal switch LH 6.5 V 19 (R)*4 (SB)*5 Ground Room lamp timer Output Other than under condition 5.0 V • Interior room lamp timer is activated. (Door is unlocked. etc...) • Welcome light function is activated. 0 V 20 (V) Ground Turn signal RH (Rear) Output Ignition switch ON Turn signal switch OFF 0 V Turn signal switch RH 6.5 V 24 (R) Ground Rear fog lamp Output Rear fog lamp OFF 0 V ON 12 V 25 (G)*6 (BR)*7 Ground Turn signal LH (Rear) Output Ignition switch ON Turn signal switch OFF 0 V Turn signal switch LH 6.5 V 26 (P)*2 (G)*3 Ground Rear wiper Output Rear wiper OFF (Stopped) 0 V ON (Operated) 12 V Terminal No. (Wire color) Description Condition Value Signal name (Approx.) Input/ + – Output PKID0926E PKID0926E PKID0926E WCS-86 < ECU DIAGNOSIS INFORMATION > BCM (BODY CONTROL MODULE) 34 (SB) Ground Luggage room antenna (−) Output Ignition switch OFF When Intelligent Key is in the passenger compartment When Intelligent Key is not in the passenger compartment 35 (V) Ground Luggage room antenna (+) Output Ignition switch OFF When Intelligent Key is in the passenger compartment When Intelligent Key is not in the passenger compartment 38 (B) Ground Back door antenna (− ) Output When the back door opener request switch is operated with ignition switch OFF When Intelligent Key is in the antenna detection area When Intelligent Key is not in the antenna detection area Terminal No. (Wire color) Description Condition Value Signal name (Approx.) Input/ + – Output JMKIA0062GB JMKIA0063GB JMKIA0062GB JMKIA0063GB JMKIA0062GB JMKIA0063GB WCS BCM (BODY CONTROL MODULE) WCS-87 < ECU DIAGNOSIS INFORMATION > C D E F G H I J K L M B A O P 39 (W) Ground Back door antenna (+) Output When the back door opener request switch is operated with ignition switch OFF When Intelligent Key is in the antenna detection area When Intelligent Key is not in the antenna detection area 47 (Y) Ground Ignition relay (IPDM E/R) control Output Ignition switch OFF or ACC 12 V ON 0 V 48 (W) Ground Back door opener switch operation Output Back door opener switch Not pressed 12 V Pressed 0 V 52 (LG) Ground Starter relay control Output Ignition switch ON (A/T models) When selector lever is in P or N position 12 V When selector lever is not in P or N position 0 V Ignition switch ON (M/T models) Battery voltage 61 (W) Ground Back door opener request switch Input Back door opener request switch ON (Pressed) 0 V OFF (Not pressed) 1.0 V 64 (V)*4 (L)*5 Ground Intelligent Key warning buzzer Output Intelligent Key warning buzzer Sounding 0 V Not sounding 12 V 65 (O) Ground Rear wiper stop position Input Rear wiper In stop position 1.0 V Not in stop position 0 V 66 (LG) Ground Back door switch Input Back door switch OFF (Door close) 12 V ON (Door open) 0 V Terminal No. (Wire color) Description Condition Value Signal name (Approx.) Input/ + – Output JMKIA0062GB JMKIA0063GB JPMIA0016GB JPMIA0016GB WCS-88 < ECU DIAGNOSIS INFORMATION > BCM (BODY CONTROL MODULE) 67 (P) Ground Back door opener switch Input Back door opener switch Pressed 0 V Not pressed 8.5 - 9.0 V 68 (BR)*6 (W)*7 Ground Rear RH door switch Input Rear RH door switch OFF (Door close) 8.5 - 9.0 V ON (Door open) 0 V 69 (R) Ground Rear LH door switch Input Rear LH door switch OFF (Door close) 8.5 - 9.0 V ON (Door open) 0 V 72 (R) Ground Room antenna 2 (−) (Center console) Output Ignition switch OFF When Intelligent Key is in the passenger compartment When Intelligent Key is not in the passenger compartment Terminal No. (Wire color) Description Condition Value Signal name (Approx.) Input/ + – Output JPMIA0594GB JPMIA0594GB JPMIA0594GB JMKIA0062GB JMKIA0063GB WCS BCM (BODY CONTROL MODULE) WCS-89 < ECU DIAGNOSIS INFORMATION > C D E F G H I J K L M B A O P 73 (G) Ground Room antenna 2 (+) (Center console) Output Ignition switch OFF When Intelligent Key is in the passenger compartment When Intelligent Key is not in the passenger compartment 74 (SB) Ground Passenger door antenna (−) Output When the passenger door request switch is operated with ignition switch OFF When Intelligent Key is in the antenna detection area When Intelligent Key is not in the antenna detection area 75 (BR) Ground Passenger door antenna (+) Output When the passenger door request switch is operated with ignition switch OFF When Intelligent Key is in the antenna detection area When Intelligent Key is not in the antenna detection area Terminal No. (Wire color) Description Condition Value Signal name (Approx.) Input/ + – Output JMKIA0062GB JMKIA0063GB JMKIA0062GB JMKIA0063GB JMKIA0062GB JMKIA0063GB WCS-90 < ECU DIAGNOSIS INFORMATION > BCM (BODY CONTROL MODULE) 76 (V) Ground Driver door antenna (−) Output When the driver door request switch is operated with ignition switch OFF When Intelligent Key is in the antenna detection area When Intelligent Key is not in the antenna detection area 77 (LG) Ground Driver door antenna (+) Output When the driver door request switch is operated with ignition switch OFF When Intelligent Key is in the antenna detection area When Intelligent Key is not in the antenna detection area 78 (Y) Ground Room antenna 1 (−) (Instrument panel) Output Ignition switch OFF When Intelligent Key is in the passenger compartment When Intelligent Key is not in the passenger compartment Terminal No. (Wire color) Description Condition Value Signal name (Approx.) Input/ + – Output JMKIA0062GB JMKIA0063GB JMKIA0062GB JMKIA0063GB JMKIA0062GB JMKIA0063GB WCS BCM (BODY CONTROL MODULE) WCS-91 < ECU DIAGNOSIS INFORMATION > C D E F G H I J K L M B A O P 79 (BR) Ground Room antenna 1 (+) (Instrument panel) Output Ignition switch OFF When Intelligent Key is in the passenger compartment When Intelligent Key is not in the passenger compartment 80 (GR) Ground NATS antenna amp. Input/ Output During waiting Ignition switch is pressed while inserting the Intelligent Key into the key slot. Just after pressing ignition switch. Pointer of tester should move. 81 (W) Ground NATS antenna amp. Input/ Output During waiting Ignition switch is pressed while inserting the Intelligent Key into the key slot. Just after pressing ignition switch. Pointer of tester should move. 82 (P)*2 (R)*3 Ground Ignition relay [Fuse block (J/B)] control Output Ignition switch OFF or ACC 0 V ON 12 V 83 (GR)*2 (Y)*3 Ground Remote keyless entry receiver communication Input/ Output During waiting When operating either button on the Intelligent Key 85 (G) Ground Alarm link Input/ Output Vehicle security system Disarmed phase 12 V Pre-armed phase or armed phase Terminal No. (Wire color) Description Condition Value Signal name (Approx.) Input/ + – Output JMKIA0062GB JMKIA0063GB JMKIA0064GB JMKIA0065GB NNKIA0175ZZ WCS-92 < ECU DIAGNOSIS INFORMATION > BCM (BODY CONTROL MODULE) 86*1 (O) Ground Dongle link Input/ Output During waiting Ignition switch is pressed while inserting the Intelligent Key into the key slot. Just after pressing ignition switch. Pointer of tester should move. 87 (BR)*6 (W)*7 Ground Combination switch INPUT 5 Input Combination switch All switches OFF (Wiper volume dial 4) 1.4 V Front fog lamp switch ON (Wiper volume dial 4) 1.3 V Rear fog lamp switch ON (Wiper volume dial 4) 1.2 V Rear wiper switch ON (Wiper volume dial 4) 1.3 V Any of the conditions below with all switches OFF • Wiper volume dial 1 • Wiper volume dial 2 • Wiper volume dial 6 • Wiper volume dial 7 1.3 V Terminal No. (Wire color) Description Condition Value Signal name (Approx.) Input/ + – Output JPMIA0041GB JPMIA0037GB JPMIA0142GB JPMIA0039GB JPMIA0040GB WCS BCM (BODY CONTROL MODULE) WCS-93 < ECU DIAGNOSIS INFORMATION > C D E F G H I J K L M B A O P 88 (V) Ground Combination switch INPUT 3 Input Combination switch All switches OFF (Wiper volume dial 4) 1.4 V Lighting switch HI (Wiper volume dial 4) 1.3 V Lighting switch 2ND (Wiper volume dial 4) 1.3 V Rear washer switch ON (Wiper volume dial 4) 1.3 V Any of the conditions below with all switches OFF • Wiper volume dial 1 • Wiper volume dial 2 • Wiper volume dial 3 1.3 V 89 (SB)*2 (L)*4 (BR)*7 Ground Push-button ignition switch (Push switch) Input Push-button ignition switch (push switch) Pressed 0 V Not pressed 12 V 90 (P) Ground CAN-L Input/ Output — — 91 (L) Ground CAN-H Input/ Output — — Terminal No. (Wire color) Description Condition Value Signal name (Approx.) Input/ + – Output JPMIA0041GB JPMIA0036GB JPMIA0037GB JPMIA0039GB JPMIA0040GB WCS-94 < ECU DIAGNOSIS INFORMATION > BCM (BODY CONTROL MODULE) 92 (LG) Ground Key slot illumination Output Key slot illumination OFF 12 V Blinking 6.5 V ON 0 V 93 (V) Ground ON indicator lamp Output Ignition switch OFF (LOCK indicator is not illuminated) Battery voltage ON or ACC 0 V 95 (O) Ground ACC relay control Output Ignition switch OFF 0 V ACC or ON 12 V 96 (GR) Ground A/T shift selector (Detention switch) power supply Output — 12 V 97 (L) Ground Steering lock condition No. 1 Input Steering lock LOCK status 0 V UNLOCK status 12 V 98 (P) Ground Steering lock condition No. 2 Input Steering lock LOCK status 12 V UNLOCK status 0 V 99 (GR)*8 (R)*9 Ground Selector lever P position switch Input Selector lever P position 0 V Any position other than P 12 V 100 (G)*6 (P)*7 Ground Passenger door request switch Input Passenger door request switch ON (Pressed) 0 V OFF (Not pressed) 1.0 V 101 (SB) Ground Driver door request switch Input Driver door request switch ON (Pressed) 0 V OFF (Not pressed) 1.0 V 102 (O) Ground Blower fan motor relay control Output Ignition switch OFF or ACC 0 V ON 12 V 103 (BR)*2 (LG)*3 Ground Remote keyless entry receiver power supply Output Ignition switch OFF 12 V Terminal No. (Wire color) Description Condition Value Signal name (Approx.) Input/ + – Output JPMIA0015GB JPMIA0016GB JPMIA0016GB WCS BCM (BODY CONTROL MODULE) WCS-95 < ECU DIAGNOSIS INFORMATION > C D E F G H I J K L M B A O P 105 (R) Ground Door lock status indicator lamp Output Door lock status indicator lamp OFF 12 V ON 0 V 106 (W) Ground Steering lock unit power supply Output Ignition switch OFF or ACC 12 V ON 0 V 107 (LG) Ground Combination switch INPUT 1 Input Combination switch (Wiper volume dial 4) All switches OFF 1.4 V Turn signal switch LH 1.3 V Turn signal switch RH 1.3 V Front wiper switch LO 1.3 V Front washer switch ON 1.3 V Terminal No. (Wire color) Description Condition Value Signal name (Approx.) Input/ + – Output JPMIA0041GB JPMIA0037GB JPMIA0036GB JPMIA0038GB JPMIA0039GB WCS-96 < ECU DIAGNOSIS INFORMATION > BCM (BODY CONTROL MODULE) 108 (R) Ground Combination switch INPUT 4 Input Combination switch All switches OFF (Wiper volume dial 4) 1.4 V Lighting switch AUTO (Wiper volume dial 4) 1.3 V Lighting switch 1ST (Wiper volume dial 4) 1.3 V Rear wiper switch INT (Wiper volume dial 4) 1.3 V Any of the conditions below with all switches OFF • Wiper volume dial 1 • Wiper volume dial 5 • Wiper volume dial 6 1.3 V Terminal No. (Wire color) Description Condition Value Signal name (Approx.) Input/ + – Output JPMIA0041GB JPMIA0038GB JPMIA0036GB JPMIA0040GB JPMIA0039GB WCS BCM (BODY CONTROL MODULE) WCS-97 < ECU DIAGNOSIS INFORMATION > C D E F G H I J K L M B A O P 109 (GR)*4 (Y)*5 Ground Combination switch INPUT 2 Input Combination switch (Wiper volume dial 4) All switches OFF 1.4 V Lighting switch PASS 1.3 V Lighting switch 2ND 1.3 V Front wiper switch AUTO 1.3 V Front wiper switch HI 1.3 V 110 (G) Ground Hazard switch Input Hazard switch ON 0 V OFF 1.1 V Terminal No. (Wire color) Description Condition Value Signal name (Approx.) Input/ + – Output JPMIA0041GB JPMIA0037GB JPMIA0036GB JPMIA0038GB JPMIA0040GB JPMIA0012GB WCS-98 < ECU DIAGNOSIS INFORMATION > BCM (BODY CONTROL MODULE) 111 (GR)*2 (Y)*3 Ground Steering lock unit communication Input/ Output Steering lock LOCK status 12 V LOCK or UNLOCK For 15 seconds after UNLOCK 12 V 15 seconds or later after UNLOCK 0 V 112 (R)*10 (GR)*11 Ground Light and rain sensor serial link Input/ Output Ignition switch ON 8.7 V 113*12 (P) Ground Optical sensor Input Ignition switch ON When bright outside of the vehicle Close to 5 V When dark outside of the vehicle Close to 0 V 114*13 (GR) Ground Clutch interlock switch Input Clutch interlock switch OFF (Clutch pedal is not depressed) 0 V ON (Clutch pedal is depressed) Battery voltage 115 (O) Ground Air bag signal Input Ignition switch OFF 0 V ACC 5.0 V ON 2.5 V 116 (BR)*2 (LG)*4 (SB)*7 Ground Stop lamp switch 1 Input — Battery voltage Terminal No. (Wire color) Description Condition Value Signal name (Approx.) Input/ + – Output JMKIA0066GB JPMIA0156GB JPMIA1034GB WCS BCM (BODY CONTROL MODULE) WCS-99 < ECU DIAGNOSIS INFORMATION > C D E F G H I J K L M B A O P 117 (Y) Ground Sensor cancel switch Input Sensor cancel switch OFF (Not pressed) 11.8 V ON (Pressed) 0 V 118 (SB)*4 (P)*5 Ground Stop lamp switch 2 (Without ICC) Input Stop lamp switch OFF (Brake pedal is not depressed) 0 V ON (Brake pedal is depressed) Battery voltage Stop lamp switch 2 (With ICC) Stop lamp switch OFF (Brake pedal is not depressed) and ICC brake hold relay OFF 0 V Stop lamp switch ON (Brake pedal is depressed) or ICC brake hold relay ON Battery voltage 119 (SB)*6 (L)*7 Ground Front door lock assembly driver side (Unlock sensor) Input Driver door LOCK status (Unlock sensor switch OFF) 8.5 - 9.0 V UNLOCK status (Unlock switch sensor ON) 0 V 120*13 (O) Ground Back-up lamp switch Input Ignition switch ON Control lever in reverse position Battery voltage Control lever in any position other than reverse 0 V 121 (BR)*2 (R)*4 (LG)*7 Ground Key slot switch Input When the Intelligent Key is inserted into key slot 12 V When the Intelligent Key is not inserted into key slot 0 V 123 (W) Ground IGN feedback Input Ignition switch OFF or ACC 0 V ON Battery voltage 124 (LG) Ground Passenger door switch Input Passenger door switch OFF (Door close) 8.5 - 9.0 V ON (Door open) 0 V Terminal No. (Wire color) Description Condition Value Signal name (Approx.) Input/ + – Output JPMIA0012GB JPMIA0594GB JPMIA0594GB WCS-100 < ECU DIAGNOSIS INFORMATION > BCM (BODY CONTROL MODULE) 132 (BR) Ground Power window switch communication Input/ Output Ignition switch ON 10.2 V Ignition switch OFF or ACC 12 V 134 (V)*4 (GR)*5 Ground LOCK indicator lamp Output LOCK indicator lamp OFF Battery voltage ON 0 V 137 (B)*2 (BR)*4 (G)*7 Ground Receiver and sensor ground Input Ignition switch ON 0 V 138*12 (Y) Ground Sensor power supply Output Ignition switch OFF 0 V ACC or ON 5 V 140 (BR)*13 (R)*14 (G)*15 (GR)*16 Ground Selector lever P/N position (A/T models) Input Selector lever P or N position 12 V Except P and N positions 0 V Park/neutral position switch (M/T models) Ignition switch ON Control lever in neutral position Battery voltage Control lever in any position other than neutral 0 V 141 (G) Ground Security indicator lamp Output Security indicator lamp ON 0 V Blinking 11.3 V OFF 12 V 142 (O) Ground Combination switch OUTPUT 5 Output Combination switch (Wiper volume dial 4) All switches OFF 0 V Lighting switch 1ST 10.7 V Lighting switch HI Lighting switch 2ND Turn signal switch RH Terminal No. (Wire color) Description Condition Value Signal name (Approx.) Input/ + – Output JPMIA0013GB JPMIA0014GB JPMIA0031GB WCS BCM (BODY CONTROL MODULE) WCS-101 < ECU DIAGNOSIS INFORMATION > C D E F G H I J K L M B A O P 143 (P) Ground Combination switch OUTPUT 1 Output Combination switch All switches OFF (Wiper volume dial 4) 0 V Front wiper switch HI (Wiper volume dial 4) 10.7 V Rear wiper switch INT (Wiper volume dial 4) Any of the conditions below with all switches OFF • Wiper volume dial 1 • Wiper volume dial 2 • Wiper volume dial 3 • Wiper volume dial 6 • Wiper volume dial 7 144 (G) Ground Combination switch OUTPUT 2 Output Combination switch All switches OFF (Wiper volume dial 4) 0 V Front washer switch ON (Wiper volume dial 4) 10.7 V Rear wiper switch ON (Wiper volume dial 4) Rear washer switch ON (Wiper volume dial 4) Any of the conditions below with all switches OFF • Wiper volume dial 1 • Wiper volume dial 5 • Wiper volume dial 6 145 (L) Ground Combination switch OUTPUT 3 Output Combination switch (Wiper volume dial 4) All switches OFF 0 V Front wiper switch AUTO 10.7 V Front wiper switch LO Lighting switch AUTO Rear fog lamp switch ON 146 (SB) Ground Combination switch OUTPUT 4 Output Combination switch (Wiper volume dial 4) All switches OFF 0 V Front fog lamp switch ON 10.7 V Lighting switch 2ND Lighting switch PASS Turn signal switch LH Terminal No. (Wire color) Description Condition Value Signal name (Approx.) Input/ + – Output JPMIA0032GB JPMIA0033GB JPMIA0034GB JPMIA0035GB WCS-102 < ECU DIAGNOSIS INFORMATION > BCM (BODY CONTROL MODULE) • *1: Only RHD models • *2: LHD gasoline engine models • *3: Except LHD gasoline engine models • *4: LHD diesel engine modelss • *5: Except LHD diesel engine models • *6: LHD models • *7: RHD models • *8: RHD gasoline engine models • *9: Except RHD gasoline engine models • *10: RHD diesel engine modelss • *11: Except RHD diesel engine models • *12: For Russia • *13: M/T models • *14: LHD A/T gasoline engine models • *15: LHD A/T diesel engine modelss • *16: RHD A/T models 150 (GR) Ground Driver door switch Input Driver door switch OFF (Door close) 8.5 - 9.0 V ON (Door open) 0 V 151 (G) Ground Rear window defogger relay control Output Rear window defogger Active 0 V Not activated Battery voltage Terminal No. (Wire color) Description Condition Value Signal name (Approx.) Input/ + – Output JPMIA0594GB WCS BCM (BODY CONTROL MODULE) WCS-103 < ECU DIAGNOSIS INFORMATION > C D E F G H I J K L M B A O P Wiring Diagram - BCM (Gasoline Engine Models) - INFOID:0000000005457389 For connector terminal arrangements, harness layouts, and alphabets in a (option abbreviation; if not described in wiring diagram), refer to GI-12, "Connector Information". JCMWM7468GB WCS-104 < ECU DIAGNOSIS INFORMATION > BCM (BODY CONTROL MODULE) JCMWM7469GB WCS BCM (BODY CONTROL MODULE) WCS-105 < ECU DIAGNOSIS INFORMATION > C D E F G H I J K L M B A O P JCMWM7470GB WCS-106 < ECU DIAGNOSIS INFORMATION > BCM (BODY CONTROL MODULE) JCMWM7471GB WCS BCM (BODY CONTROL MODULE) WCS-107 < ECU DIAGNOSIS INFORMATION > C D E F G H I J K L M B A O P JCMWM7472GB WCS-108 < ECU DIAGNOSIS INFORMATION > BCM (BODY CONTROL MODULE) Wiring Diagram - BCM (Diesel Engine Models) - INFOID:0000000006091806 For connector terminal arrangements, harness layouts, and alphabets in a (option abbreviation; if not described in wiring diagram), refer to GI-12, "Connector Information". JCMWM7473GB WCS BCM (BODY CONTROL MODULE) WCS-109 < ECU DIAGNOSIS INFORMATION > C D E F G H I J K L M B A O P JCMWM7474GB WCS-110 < ECU DIAGNOSIS INFORMATION > BCM (BODY CONTROL MODULE) JCMWM7475GB WCS BCM (BODY CONTROL MODULE) WCS-111 < ECU DIAGNOSIS INFORMATION > C D E F G H I J K L M B A O P JCMWM7476GB WCS-112 < ECU DIAGNOSIS INFORMATION > BCM (BODY CONTROL MODULE) Fail-safe INFOID:0000000005457390 FAIL-SAFE CONTROL BY DTC BCM performs fail-safe control when any DTC are detected. JCMWM7477GB WCS BCM (BODY CONTROL MODULE) WCS-113 < ECU DIAGNOSIS INFORMATION > C D E F G H I J K L M B A O P Display contents of CONSULT Fail-safe Cancellation B2013: ID DISCORD BCM-S/L Inhibit engine cranking Erase DTC B2014: CHAIN OF S/L-BCM Inhibit engine cranking Erase DTC B2190: NATS ANTENNA AMP Inhibit engine cranking Erase DTC B2191: DIFFERENCE OF KEY Inhibit engine cranking Erase DTC B2192: ID DISCORD BCM-ECM Inhibit engine cranking Erase DTC B2193: CHAIN OF BCM-ECM Inhibit engine cranking Erase DTC B2195: ANTI SCANNING Inhibit engine cranking Ignition switch ON → OFF B2196: DONGLE NG Inhibit engine cranking Erase DTC B2557: VEHICLE SPEED Inhibit steering lock When normal vehicle speed signals are received from ABS actuator and electric unit (control unit) for 500 ms B2560: STARTER CONT RELAY Inhibit engine cranking 500 ms after the following CAN signal communication status becomes consistent • Starter control relay signal • Starter relay status signal B2601: SHIFT POSITION Inhibit steering lock 500 ms after the following signal reception status becomes consistent • Selector lever P position switch signal • P range signal (CAN) B2602: SHIFT POSITION Inhibit steering lock 5 seconds after the following BCM recognition conditions are fulfilled • Ignition switch is in the ON position • Selector lever P position switch signal: Except P position (12 V) • Vehicle speed: 4 km/h (2.5 MPH) or more B2603: SHIFT POSI STATUS Inhibit steering lock 500 ms after the following BCM recognition conditions are fulfilled • Ignition switch is in the ON position • Selector lever P position switch signal: Except P position (12 V) • Selector lever P/N position signal: Except P and N positions (0 V) B2604: PNP/CLUTCH SW Inhibit steering lock 500 ms after any of the following BCM recognition conditions are fulfilled • Status 1 - Ignition switch is in the ON position - Selector lever P/N position signal: P and N position (12 V) - P range signal or N range signal (CAN): ON • Status 2 - Ignition switch is in the ON position - Selector lever P/N position signal: Except P and N positions (0 V) - P range signal and N range signal (CAN): OFF B2605: PNP/CLUTCH SW Inhibit steering lock 500 ms after any of the following BCM recognition conditions are fulfilled • Ignition switch is in the ON position - Power position: IGN - Selector lever P/N position signal: Except P and N positions (0 V) - Interlock/PNP switch signal (CAN): OFF • Status 2 - Ignition switch is in the ON position - Selector lever P/N position signal: P or N position (12 V) - Interlock/PNP switch signal (CAN): ON B2606: S/L RELAY Inhibit engine cranking 500 ms after the following CAN signal communication status becomes consistent • Steering lock relay signal (Request signal) • Steering lock relay signal (Condition signal) B2607: S/L RELAY Inhibit engine cranking 500 ms after the following CAN signal communication status becomes consistent • Steering lock relay signal (Request signal) • Steering lock relay signal (Condition signal) WCS-114 < ECU DIAGNOSIS INFORMATION > BCM (BODY CONTROL MODULE) FAIL-SAFE CONTROL BY LIGHT AND RAIN SENSOR MALFUNCTION BCM detects the light and rain sensor serial link error and the light and rain sensor malfunction. BCM controls the following fail-safe when light and rain sensor has a malfunction. Fail-safe Control • Auto light control: Headlamp low beam, parking lamp, license plate lamp and tail lamp are turned ON. B2608: STARTER RELAY Inhibit engine cranking 500 ms after the following signal communication status becomes consistent • Starter motor relay control signal • Starter relay status signal (CAN) B2609: S/L STATUS • Inhibit engine cranking • Inhibit steering lock When the following steering lock conditions agree • BCM steering lock control status • Steering lock condition No. 1 signal status • Steering lock condition No. 2 signal status B260A: IGNITION RELAY Inhibit engine cranking 500 ms after the following conditions are fulfilled • IGN relay (IPDM E/R) control signal: OFF (12 V) • Ignition ON signal (CAN to IPDM E/R): OFF (Request signal) • Ignition ON signal (CAN from IPDM E/R): OFF (Condition signal) B260F: ENG STATE SIG LOST Maintains the power supply position attained at the time of DTC detection When any of the following conditions are fulfilled • Power position changes to ACC • Receives engine status signal (CAN) B2612: S/L STATUS • Inhibit engine cranking • Inhibit steering lock When any of the following conditions are fulfilled • Steering lock unit status signal (CAN) is received normally • The BCM steering lock control status matches the steering lock status recognized by the steering lock unit status signal (CAN from IPDM E/R) B2617: BCM Inhibit engine cranking 1 second after the starter motor relay control inside BCM becomes normal B2618: BCM Inhibit engine cranking 1 second after the ignition relay (IPDM E/R) control inside BCM becomes normal B2619: BCM Inhibit engine cranking 1 second after the steering lock unit power supply output control inside BCM becomes normal B261E: VEHICLE TYPE Inhibit engine cranking BCM initialization B261F: ASCD CNCL/CLTCH SW Inhibit steering lock When any of the following conditions are fulfilled • Power supply position: ON • Receives clutch switch signal (CAN from ECM): OFF B2620: NEUTRAL SW Inhibit engine cranking (Only when try to start the engine while depressing brake pedal and shifting to the neutral position) When any of the following BCM recognition conditions are fulfilled • Status 1 - Back up lamp switch signal: ON (Battery voltage) - Park/neutral position switch signal: OFF (0 V) • Status 2 - Back-up lamp switch signal: OFF (0 V) - Park/neutral position switch signal: ON (Battery voltage) • Status 3 - Back-up lamp switch signal: OFF (0 V) - Park/neutral position switch signal: OFF (0 V) B26E8: CLUTCH SW Inhibit engine cranking When any of the following BCM recognition conditions are fulfilled • Status 1 - ASCD clutch switch signal (CAN from ECM): ON - Clutch interlock switch signal: OFF (0 V) • Status 2 - ASCD clutch switch signal (CAN from ECM): OFF - Clutch interlock switch signal: ON (Battery voltage) B26E9: S/L STATUS • Inhibit engine cranking • Inhibit steering lock When BCM transmits the LOCK request signal to steering lock unit, and receives LOCK response signal from steering lock unit, the following conditions are fulfilled • Steering condition No. 1 signal: LOCK (0V) • Steering condition No. 2 signal: LOCK (12 V) Display contents of CONSULT Fail-safe Cancellation WCS BCM (BODY CONTROL MODULE) WCS-115 < ECU DIAGNOSIS INFORMATION > C D E F G H I J K L M B A O P • Front wiper control - Front wiper switch AUTO and sensing rain drop: The condition just before the activation of fail-safe is maintained until the front wiper switch is turned OFF. - Front wiper switch AUTO and not sensing rain drop: Front wiper is LO operation until the front wiper switch is turned off. REAR WIPER MOTOR PROTECTION BCM detects the rear wiper stopping position according to the rear wiper stop position signal. When the rear wiper stop position signal does not change for more than 5 seconds while driving the rear wiper, BCM stops power supply to protect the rear wiper motor. Condition of cancellation 1. More than 1 minute is passed after the rear wiper stop. 2. Turn rear wiper switch OFF. 3. Operate the rear wiper switch or rear washer switch. DTC Inspection Priority Chart INFOID:0000000005457391 If some DTCs are displayed at the same time, perform inspections one by one based on the following priority chart. Priority DTC 1 B2562: LOW VOLTAGE 2 • U1000: CAN COMM • U1010: CONTROL UNIT(CAN) 3 • B2190: NATS ANTENNA AMP • B2191: DIFFERENCE OF KEY • B2192: ID DISCORD BCM-ECM • B2193: CHAIN OF BCM-ECM • B2195: ANTI SCANNING • B2196: DONGLE NG WCS-116 < ECU DIAGNOSIS INFORMATION > BCM (BODY CONTROL MODULE) DTC Index INFOID:0000000005457392 NOTE: The details of time display are as follows. • CRNT: A malfunction is detected now. • PAST: A malfunction was detected in the past. IGN counter is displayed on Freeze Frame Data. For details of Freeze Frame Data, refer to BCS-22, "COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM)". 4 • B2013: ID DISCORD BCM-S/L • B2014: CHAIN OF S/L-BCM • B2553: IGNITION RELAY • B2555: STOP LAMP • B2556: PUSH-BTN IGN SW • B2557: VEHICLE SPEED • B2560: STARTER CONT RELAY • B2601: SHIFT POSITION • B2602: SHIFT POSITION • B2603: SHIFT POSI STATUS • B2604: PNP/CLUTCH SW • B2605: PNP/CLUTCH SW • B2606: S/L RELAY • B2607: S/L RELAY • B2608: STARTER RELAY • B2609: S/L STATUS • B260A: IGNITION RELAY • B260B: STEERING LOCK UNIT • B260C: STEERING LOCK UNIT • B260D: STEERING LOCK UNIT • B260F: ENG STATE SIG LOST • B2612: S/L STATUS • B2614: BCM • B2615: BCM • B2616: BCM • B2617: BCM • B2618: BCM • B2619: BCM • B261A: PUSH-BTN IGN SW • B261E: VEHICLE TYPE • B261F: ASCD CNCL/CLTCH SW • B2620: NEUTRAL SW • B26E8: CLUTCH SW • B26E9: S/L STATUS • B26EA: KEY REGISTRATION • U0415: VEHICLE SPEED 5 • B2621: INSIDE ANTENNA • B2622: INSIDE ANTENNA • B2623: INSIDE ANTENNA 6 B26E7: TPMS CAN COMM Priority DTC CONSULT display Fail-safe Freeze Frame Data •Vehicle Speed •Odo/Trip Meter •Vehicle Condition Intelligent Key warning lamp ON Reference page No DTC is detected. Further testing may be required. — — — — U1000: CAN COMM — — — BCS-40 U1010: CONTROL UNIT(CAN) — — — BCS-41 U0415: VEHICLE SPEED — — — BCS-42 B2013: ID DISCORD BCM-S/L × × — SEC-56 WCS BCM (BODY CONTROL MODULE) WCS-117 < ECU DIAGNOSIS INFORMATION > C D E F G H I J K L M B A O P B2014: CHAIN OF S/L-BCM × × — SEC-57 B2190: NATS ANTENNA AMP × — — SEC-47 B2191: DIFFERENCE OF KEY × — — SEC-50 B2192: ID DISCORD BCM-ECM × — — SEC-51 B2193: CHAIN OF BCM-ECM × — — SEC-52 B2195: ANTI SCANNING × — — SEC-53 B2196: DONGLE NG × — — SEC-54 B2553: IGNITION RELAY — × — PCS-55 B2555: STOP LAMP — × — SEC-60 B2556: PUSH-BTN IGN SW — × × SEC-62 B2557: VEHICLE SPEED × × × SEC-64 B2560: STARTER CONT RELAY × × × SEC-65 B2562: LOW VOLTAGE — × — BCS-43 B2601: SHIFT POSITION × × × SEC-66 B2602: SHIFT POSITION × × × SEC-69 B2603: SHIFT POSI STATUS × × × SEC-71 B2604: PNP/CLUTCH SW × × × SEC-74 B2605: PNP/CLUTCH SW × × × SEC-76 B2606: S/L RELAY × × × SEC-78 B2607: S/L RELAY × × × SEC-79 B2608: STARTER RELAY × × × SEC-81 B2609: S/L STATUS × × × SEC-83 B260A: IGNITION RELAY × × × PCS-57 B260B: STEERING LOCK UNIT — × × SEC-87 B260C: STEERING LOCK UNIT — × × SEC-88 B260D: STEERING LOCK UNIT — × × SEC-89 B260F: ENG STATE SIG LOST × × × SEC-90 B2612: S/L STATUS × × × SEC-91 B2614: BCM — × × PCS-59 B2615: BCM — × × PCS-61 B2616: BCM — × × PCS-63 B2617: BCM × × × SEC-95 B2618: BCM × × × PCS-65 B2619: BCM × × × SEC-97 B261A: PUSH-BTN IGN SW — × × PCS-66 B261E: VEHICLE TYPE × × × (Turn ON for 15 seconds) SEC-98 B261F: ASCD CNCL/CLTCH SW × × × SEC-99 B2620: NEUTRAL SW × × × SEC-101 B2621: INSIDE ANTENNA — × — DLK-68*1 DLK-326*2 B2622: INSIDE ANTENNA — × — DLK-70*1 DLK-328*2 CONSULT display Fail-safe Freeze Frame Data •Vehicle Speed •Odo/Trip Meter •Vehicle Condition Intelligent Key warning lamp ON Reference page WCS-118 < ECU DIAGNOSIS INFORMATION > BCM (BODY CONTROL MODULE) • *1: With super lock • *2: Without super lock B2623: INSIDE ANTENNA — × — DLK-72*1 DLK-330*2 B26E7: TPMS CAN COMM — — — BCS-44 B26E8: CLUTCH SW × × × SEC-104 B26E9: S/L STATUS × × × (Turn ON for 15 seconds) SEC-106 B26EA: KEY REGISTRATION — × × (Turn ON for 15 seconds) SEC-107 CONSULT display Fail-safe Freeze Frame Data •Vehicle Speed •Odo/Trip Meter •Vehicle Condition Intelligent Key warning lamp ON Reference page WCS THE PARKING BRAKE RELEASE WARNING CONTINUES SOUNDING, OR DOES NOT SOUND WCS-119 < SYMPTOM DIAGNOSIS > C D E F G H I J K L M B A O P SYMPTOM DIAGNOSIS THE PARKING BRAKE RELEASE WARNING CONTINUES SOUNDING, OR DOES NOT SOUND Description INFOID:0000000004968298 • The parking brake warning buzzer sounds continuously during vehicle travel though the parking brake is released • The parking brake warning buzzer does not sound at all even though driving the vehicle with the parking brake applied. Diagnosis Procedure INFOID:0000000004968299 1.CHECK PARKING BRAKE WARNING LAMP 1. Start the engine. 2. Check the operation of the brake warning lamp by operating the parking brake. Is the inspection result normal? YES >> Replace the combination meter. NO >> GO TO 2. 2.CHECK PARKING BRAKE SWITCH SIGNAL CIRCUIT Perform a check for the parking brake switch signal circuit. Refer to MWI-72, "Diagnosis Procedure". Is the inspection result normal? YES >> GO TO 3. NO >> Repair harness or connector. 3.CHECK PARKING BRAKE SWITCH UNIT Perform a unit check for the parking brake switch. Refer to BRC-90, "Component Inspection". Is the inspection result normal? YES >> Replace the combination meter. NO >> Replace the parking brake switch. Refer to PB-7, "PEDAL TYPE : Removal and Installation" (A/T models) or PB-8, "LEVER TYPE : Removal and Installation" (M/T models). Parking brake applied : ON Parking brake released : OFF WCS-120 < SYMPTOM DIAGNOSIS > THE LIGHT REMINDER WARNING DOES NOT SOUND THE LIGHT REMINDER WARNING DOES NOT SOUND Description INFOID:0000000004968300 Light reminder warning chime does not sound even though headlamp is illuminated. Diagnosis Procedure INFOID:0000000004968301 1.CHECK COMBINATION SWITCH (LIGHT SWITCH) OPERATION Check that the tail lamps operate normally by operating the combination switch (light switch). Do they operate normally? YES >> GO TO 2. NO >> Refer to EXL-208, "WITH DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure". 2.CHECK FRONT DOOR SWITCH (DRIVER SIDE) SIGNAL CIRCUIT Perform the check for the front door switch (driver side) signal circuit. Refer to DLK-75, "Diagnosis Procedure" (WITH SUPER LOCK) or DLK-333, "Diagnosis Procedure" (WITHOUT SUPER LOCK). Is the inspection result normal? YES >> Replace BCM. Refer to BCS-94, "Removal and Installation". NO >> Repair or replace the malfunctioning parts. WCS THE SEAT BELT (REMINDER) WARNING CONTINUES SOUNDING, OR DOES NOT SOUND WCS-121 < SYMPTOM DIAGNOSIS > C D E F G H I J K L M B A O P THE SEAT BELT (REMINDER) WARNING CONTINUES SOUNDING, OR DOES NOT SOUND EXCEPT FOR RUSSIA EXCEPT FOR RUSSIA : Description INFOID:0000000004968302 • Seat belt reminder warning does not sound. • Seat belt reminder warning sounds continuously. EXCEPT FOR RUSSIA : Diagnosis Procedure INFOID:0000000004968303 1.CHECK UNIFIED METER AND A/C AMP. INPUT SIGNAL (1) With CONSULT-III Select “Data Monitor” of the “METER/M&A” and check the “BUCKLE SW” monitor value. Refer to WCS-28, "Component Function Check". Without CONSULT-III 1. Turn ignition switch ON. 2. Check voltage between unified meter and A/C amp. harness connector and ground. Is the inspection result normal? YES >> GO TO 4. NO >> GO TO 2. 2.CHECK SEAT BELT BUCKLE SWITCH (DRIVER SIDE) SIGNAL CIRCUIT 1. Turn ignition switch OFF. 2. Check the seat belt buckle switch (driver side) signal circuit. Refer to WCS-28, "Diagnosis Procedure". Is the inspection result normal? YES >> GO TO 3. NO >> Repair harness or connector. 3.CHECK SEAT BELT BUCKLE SWITCH UNIT (DRIVER SIDE) Perform a unit check for the seat belt buckle switch (driver side). Refer to WCS-29, "Component Inspection". Is the inspection result normal? YES >> Replace unified meter and A/C amp. NO >> Replace seat belt buckle (driver side). 4.CHECK UNIFIED METER AND A/C AMP. INPUT SIGNAL (2) Check voltage between unified meter and A/C amp. harness connector and ground. Terminals Condition Voltage (Approx.) (+) (-) Unified meter and A/C amp. Ground Connector Terminal M66 9 When driver seat belt is fastened When driver seat belt is unfastened 0 V JPNIA1177ZZ WCS-122 < SYMPTOM DIAGNOSIS > THE SEAT BELT (REMINDER) WARNING CONTINUES SOUNDING, OR DOES NOT SOUND Is the inspection result normal? YES >> Replace unified meter and A/C amp. NO >> GO TO 5. 5.CHECK SEAT BELT BUCKLE SWITCH (PASSENGER SIDE) SIGNAL CIRCUIT 1. Turn ignition switch OFF. 2. Check the seat belt buckle switch (passenger side) signal circuit. Refer to WCS-30, "Diagnosis Procedure". Is the inspection result normal? YES >> GO TO 6. NO >> Repair harness or connector. 6.CHECK SEAT BELT BUCKLE SWITCH UNIT (PASSENGER SIDE) Perform a unit check for the seat belt buckle switch (passenger side). Refer to WCS-30, "Component Inspection". Is the inspection result normal? YES >> GO TO 7. NO >> Replace seat belt buckle (passenger side). 7.CHECK OCCUPANT DETECTION UNIT Perform a unit check for the occupant detection unit. Refer to WCS-30, "Component Inspection". Is the inspection result normal? YES >> Replace unified meter and A/C amp. NO >> Replace occupant detection unit. FOR RUSSIA FOR RUSSIA : Description INFOID:0000000006066789 • Seat belt warning does not sound even though driver seat belt is not fastened. • Seat belt warning sounds even though driver seat belt is fastened. FOR RUSSIA : Diagnosis Procedure INFOID:0000000006059754 1.CHECK UNIFIED METER AND A/C AMP. INPUT SIGNAL With CONSULT-III Select “Data Monitor” of the “METER/M&A” and check the “BUCKLE SW” monitor value. Refer to WCS-28, "Component Function Check". Without CONSULT-III 1. Turn ignition switch ON. 2. Check voltage between unified meter and A/C amp. harness connector and ground. Terminals Condition Voltage (Approx.) (+) (-) Unified meter and A/C amp. Ground Connector Terminal M66 12 • When passenger seat belt is fastened • When getting in the passenger seat 12 V • When passenger seat belt is unfastened • When getting in the passenger seat 0 V WCS THE SEAT BELT (REMINDER) WARNING CONTINUES SOUNDING, OR DOES NOT SOUND WCS-123 < SYMPTOM DIAGNOSIS > C D E F G H I J K L M B A O P Is the inspection result normal? YES >> Replace BCM. NO >> GO TO 2. 2.CHECK SEAT BELT BUCKLE SWITCH (DRIVER SIDE) SIGNAL CIRCUIT 1. Turn ignition switch OFF. 2. Check the seat belt buckle switch (driver side) signal circuit. Refer to WCS-28, "Diagnosis Procedure". Is the inspection result normal? YES >> GO TO 3. NO >> Repair harness or connector. 3.CHECK SEAT BELT BUCKLE SWITCH (DRIVER SIDE) Perform a unit check for the seat belt buckle switch (driver side). Refer to WCS-29, "Component Inspection". Is the inspection result normal? YES >> Replace unified meter and A/C amp. NO >> Replace seat belt buckle (driver side). Refer to SB-9, "SEAT BELT BUCKLE : Exploded View". Terminals Condition Voltage (Approx.) (+) (-) Unified meter and A/C amp. Ground Connector Terminal M66 9 When driver seat belt is fastened When driver seat belt is unfastened 0 V JPNIA1177ZZ WCS-124 < PRECAUTION > PRECAUTIONS PRECAUTION PRECAUTIONS EXCEPT FOR RUSSIA EXCEPT FOR RUSSIA : Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" INFOID:0000000005383566 The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision. Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this Service Manual. WARNING: • To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision which would result in air bag inflation, all maintenance must be performed by an authorized NISSAN/INFINITI dealer. • Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module, see the “SRS AIR BAG”. • Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors. PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS WARNING: • When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing serious injury. • When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the battery, and wait at least 3 minutes before performing any service. FOR RUSSIA FOR RUSSIA : Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" INFOID:0000000006069572 The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted. Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this Service Manual. WARNING: • To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision that would result in air bag inflation, all maintenance must be performed by an authorized NISSAN/INFINITI dealer. • Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module, see the “SRS AIR BAG”. • Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors. PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS WARNING: • When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) WCS PRECAUTIONS WCS-125 < PRECAUTION > C D E F G H I J K L M B A O P with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing serious injury. • When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the battery, and wait at least 3 minutes before performing any service. Precaution for Battery Service (for V9X Models) INFOID:0000000006059207 When disconnect the battery cable, pay attention to the following. • Always use a 12 volt battery as power source. • Do not attempt to disconnect battery cables while engine is running. • Before disconnecting battery cables, turn ignition switch OFF and wait at least 4 minutes. • After high-load driving, turn the ignition switch OFF and wait for at least 15 minutes to remove the battery cable. NOTE: Turbocharger cooling pump may operate in a few minutes after the ignition switch is turned OFF. |